Canberra 9233653E V3.0 Error Codes

214 codes from pages 381–448 of the manual

This is the list of error codes the Canberra manual gives for the 9233653E V3.0 Genie™ 2000 Spectroscopy Software. Find your code below and open it for what the manual says about its causes and what to do.

Error codes from p. 381

CodeWhat it meansPage
805A Parameter not on file. p. 381
8092 Failed to find, access or open file. p. 381
809A Error closing file. p. 381
80A2 Error reading from file. p. 381
80AA Error writing to file. p. 381
8102 Block (class) not on file. p. 381
8362 Number too large for storage. p. 381
8E2A File is open and not shareable. p. 381
8E62 File already exists. p. 381
8E6A Invalid file name. p. 382
8E7A Destination file is open. p. 382
FFFE Timeout during communications with VDM. p. 382
FFF4 Network Configuration File error. p. 382
F3 Error -13 attempting communication with VDM. p. 382
-nn Error (-nn) communicating with VDM. p. 382
7: A path named by an environment variable was not found. p. 382
C A required environment variable was not found by the VDM. p. 383
13 Datasource is unknown to the VDM. p. 383
17 Action disabled – datasource not verified p. 383
19 Can’t effect change of busy datasource in Runtime Database p. 383
21 Major verification error encountered when opening the specified detector datasource. p. 383
22 Busy but never opened. p. 383
23 Minor verification error encountered when opening the specified detector datasource. p. 383
1 Function not supported by this algorithm p. 383
2 ROI is too small to solve p. 383
3 Too few points for the calculation. p. 383
4 Parsing error(s) detected. p. 401
96EA Could not fit peak(s) due to bad fit shape parameters p. 388
100 Can't open file with mu-library. Check the existence of the file pointed to by the :ATTENUATION_LIBRARY statement in file SPACE.INI. p. 438
101 Can't find predefined material in the library. The material assigned for some geometry component is absent in the connected library. Insert the desired material into the library. p. 438
102 Error while reading the attenuation library. Problem with the mu-library. The library may be corrupted; use its backup version. p. 438
103 Arrays to store attenuation coeffs. are full. Only 10 energy intervals may be used to describe the polynomial that represents the energy dependence of mass attenuation coefficient. p. 438
104 End of file with mu-library is reached, no more records exist. p. 388
500 Error while accessing of a function in LoadMuLibr.dll. The DLL may be corrupted; re-install it. p. 438
501 Cannot find LoadMuLibr.dll. p. 388
502 Error during treatment of substance composition. The old mu-library format may have been used. You may use either the construction of a new substance from elements (via chemical formula) and/or the substances prepared in the Windows version of the mu-library editor. p. 438
503 Error during conversion of the formula to the new mu-library format. While reading the DOS formatted Mu-Library the program was unable to convert a substance composition into the new format. Try to prepare this substance directly using the Windows version of the program. p. 438
504 Error in DLL (.dll) while performing the selected operation. p. 388
505 Cannot load the ISOCOS path data. Either file SPACE.INI was not found or the statement :ATTENUATION_LIBRARY was not found in SPACE.INI. p. 438
506 Error while deleting a material from the library. Internal error in muedit.dll. p. 438
1018 Cannot open efficiency (.ECC) file generated by ISOCS. p. 394
1019 Error while reading ISOCS efficiency (.ECC) file: invalid number of columns in file. p. 394
1020 Error while reading ISOCS efficiency (.ECC) file: invalid number of energies in file. p. 394
1021 Internal error calling efficiency curve function in .dll. p. 394
1022 Error returned from efficiency curve function in .dll. p. 394
1023 Cannot load .dll. Check existence of this file in the directory specified by the :PROGRAM keyword in Space.ini. p. 394
1024 Internal error: generation failed. p. 394
1025 Error attempting to open .ECC file generated by ISOCS: cannot find :ECC_OUTPUT keyword in file Space.ini. p. 394
1026 Unrecognized file format: the file is not in a .GEO format. p. 394
1027 The function computing efficiency returned with an error. p. 394
1028 Internal system error attempting to call a function in _generic.dll. p. 394
1029 Cannot load _generic.dll. p. 394
1030 The geometry (.GEO) file was created by later version of Geometry Composer than is currently running. The program may have failed attempting to read a file. Please update your Geometry Composer. p. 444
1031 Cannot open file containing geometry data. p. 394
1032 Internal arrays for importing ISOCS geometry are full. Check the .GIS file and insure that all contained data are valid. p. 444
1033 Cannot open the Clipboard to store the template picture for export to Excel. p. 394
1034 Cannot empty the Clipboard. p. 394
1035 Unable to write template picture to the Clipboard. p. 394
1036 Do you wish to overwrite existing configuration file? p. 394
1054 Cannot delete temporary file .txt p. 396
1055 Cannot open temporary file to store beaker description during geometry testing. p. 396
1056 Cannot find generated file. p. 396
1057 Excel is being launched... p. 396
1058 Cannot launch ‘Excel’. p. 396
1059 Efficiency curve may be generated after saving the geometry file p. 396
1060 Geometry test has run successfully p. 396
1061 Geometry test has failed: p. 396
1062 Error p. 396
1063 Variable ‘SPACE’ is not found in the environment. p. 396
1064 File Space.ini cannot be opened. p. 396
1065 The preset statement is not found in file Space.ini p. 396
1066 Cannot open file detector. with detector parameters. p. 396
1067 Error in format of file Space.ini. p. 396
1101 Cannot find the bitmap containing the template drawing. p. 396
1102 Please select the energy to be deleted p. 396
1103 An Efficiency Calibration Calculation (ECC) process is already running. p. 396
1104 Efficiency data points have been generated p. 396
LGT_101 Windows sockets initialization failed. p. 398
LGT_104 Windows sockets initialization failed. p. 398
LGT_106 Windows sockets initialization failed. p. 398
LGT_107 Windows sockets initialization failed. p. 398
5 Temp. file creation error. p. 401
6 Error communicating with VDM. p. 401
8 Error during CAM file access. p. 401
9 Invalid intermediate file p. 401
380 General communication failure. p. 401
381 Memory allocation error. p. 401
384 The record being transferred has the same time-stamp as one that's already on file - but there's no over-write flag. p. 401
385 No records to transfer. p. 401
386 Nuclide or Nuclide line not found. p. 401
38C Warning that the bias test was not performed because one or more values had error = 0. p. 401
38D Bad date range specified. p. 401
38E Warning that not all tests were performed. p. 401
#256 AN EFFICIENCY CALIBRATION CALCULATION (ECC) PROCESS IS ALREADY RUNNING. p. 408
#257 CAN'T OPEN INPUT FILE WITH THE TEMPLATE DESCRIPTION. p. 408
#258 UNKNOWN TEMPLATE NAME. p. 408
#259 TEMPLATE NAME IS MISSING. p. 408
#260 CAN'T ALLOCATE MEMORY TO READ THE FILE WITH THE TEMPLATE DESCRIPTION. p. 408
#261 FILE WITH TEMPLATE DESCRIPTION IS EMPTY. p. 408
#270 FILE WITH LIST OF RECTANGULAR COLLIMATORS IS NOT FOUND. p. 410
#272 FILE WITH LIST OF HOUSINGS IS NOT FOUND. p. 410
#273 FILE NAME WITH THE PREDEFINED ENERGY LIST IS NOT FOUND. p. 410
#274 THE DCG FILE FORMAT IS INCOMPATIBLE WITH THE LabSOCS/ISOCS SOFTWARE VERSION. p. 410
#275 NOT ENOUGH ROOM FOR ABSORBER. p. 410
#276 DETECTOR IS BEHIND THE ABSORBER. p. 410
#319 CAN'T OPEN 'SPACE.INI' FILE. p. 416
#320 THE 'SPACE.INI' FILE IS EMPTY. p. 416
#322 THE :SPACE_CALIBRATION KEYWORD IS MISSING IN 'SPACE.INI' FILE. p. 416
#323 THE :SOURCE_PARAMETERS KEYWORD IS MISSING IN 'SPACE.INI' FILE. p. 416
#324 THE :ATTENUATION_LIBRARY KEYWORD IS MISSING IN 'SPACE.INI' FILE. p. 416
#326 THE :TABLE_KIT KEYWORD IS MISSING IN 'SPACE.INI' FILE. p. 416
#327 THE :ECC_OUTPUT KEYWORD IS MISSING IN 'SPACE.INI' FILE. p. 416
#328 THE :COINCIDENCE KEYWORD IS MISSING IN 'SPACE.INI' FILE. p. 416
#335 ORDER NUMBER OF THE TEMPLATE NAME IS MISSING. p. 418
#336 CAN'T OPEN ECC_DATA FILE TO RETRIEVE THE TEMPLATE PARAMETERS FROM DISK. p. 418
#337 ECC_DATA FILE CONTAINS AN INVALID TEMPLATE NAME. p. 418
#338 THE NUMBER OF ITERATIONS FOR ECC INTEGRATION MUST BE GREATER THAN OR EQUAL TO 3. p. 418
#339 CAN'T WRITE BACK FILE FOR THE RUN+ADD MODE OF . p. 418
#340 CAN'T CREATE FILE TO WRITE THE ECC RESULTS. p. 418
#348 THE :UW_HOUSING KEYWORD IS MISSING IN 'SPACE.INI' FILE. p. 420
#349 ECC WAS INTERRUPTED DUE TO PROGRESS BAR ERROR: Can't find ISOCSS_CreateProgressBar function. p. 420
#350 ECC WAS INTERRUPTED DUE TO PROGRESS BAR ERROR: Can't find ISOCSS_RefreshProgressBar function. p. 420
#351 ECC WAS INTERRUPTED DUE TO PROGRESS BAR ERROR: Can't find ISOCSS_DestroyProgressBar function. p. 420
#352 ECC WAS INTERRUPTED DUE TO PROGRESS BAR ERROR: Can't destroy Progress Bar. p. 420
#353 ECC WAS INTERRUPTED DUE TO PROGRESS BAR ERROR: Can't Create Progress Bar. p. 420
#354 ECC WAS INTERRUPTED DUE TO PROGRESS BAR ERROR: Can't Refresh Progress Bar. p. 420
#355 ECC INTERRUPTED BY USER. p. 420
#356 SPACE AVAILABLE ON DISK IS NOT ENOUGH TO WRITE COINCIDENCE CALCULATION DATA. p. 420
#357 THE :DETECTOR_PAR KEYWORD IS MISSING IN 'SPACE.INI' FILE. p. 420
#362 DECLARED HOUSING NAME IS NOT FOUND. p. 422
#363 DECLARED DETECTOR NAME IS NOT FOUND. p. 422
#364 THE :PREDEFINED_ELIST KEYWORD IS MISSING IN 'SPACE.INI' FILE. p. 422
#365 TEMPLATE NAME USED IN THE GEOMETRY DESCRIPTION FILE IS TOO LONG. p. 422
#366 THE NAME OF THE BEAKER DESCRIPTION FILE USED IN THE GEOMETRY FILE IS TOO LONG. p. 422
#367 HOUSING NAME IS TOO LONG. p. 422
#374 INVALID DENSITY UNIT. p. 424
#375 INVALID PRESSURE UNIT. p. 424
#376 INVALID TEMPERATURE UNIT. p. 424
#377 FILE INTENDED TO STORE THE RESULTS HAS A LONG NAME. p. 424
#378 FULL FILE NAME PATH IS TOO LONG. p. 424
#601 SAMPLE IS OUT OF THE COMPLEX BOX CONTAINER. SEE THE SOURCE TABLE. p. 424
#602 AN INVALID DIMENSION IN THE RECTANGULAR HOT SPOT. CHECK THE HOT SPOT DIMENSIONS IN SOURCE TABLE. p. 424
#902 UNDERWATER HOUSING OR COLLIMATOR IS IN CONFLICT WITH MARINELLI REFERENCE PLANE. p. 426
#951 A NEGATIVE DIMENSION VALUE IS INDICATED IN THE PIPE TEMPLATE. CHECK TABLE OF SAMPLE PARAMETERS. p. 426
#952 PIPE DIAMETER IS TOO SMALL. NOT ENOUGH ROOM FOR SOURCE No.2. p. 426
#1001 SPHERICAL SOURCE IS OUT OF DRUM. p. 426
#1051 AO VALUE IS OUT OF THE [0,1] LIMIT. REENTER AO.. p. 426
#1052 DMAX IS GREATER THAN SOURCE THICKNESS. REENTER DMAX. p. 426
#1053 DRL VALUE MUST BE POSITIVE. REENTER DRL. p. 426
#1108 A NEGATIVE DIAMETER VALUE IS FOUND IN THE BEAKER DESCRIPTION FILE. p. 428
#1109 DENSITY VALUE IS NOT ALLOWED IF DEFAULT MATERIAL NAME IS USED IN THE BEAKER DESCRIPTION FILE. p. 428
#1110 NEITHER A MATERIAL NAME NOR A DENSITY IS ALLOWED FOR A BOUNDARY FRAGMENT IN THE BEAKER DESCRIPTION FILE. p. 428
#1111 NUMBER OF FRAGMENTS USED IN THE BEAKER DESCRIPTION FILE EXCEEDS 200. p. 428
#1116 INNER CONTOUR IS MISSING IN THE BEAKER DESCRIPTION FILE. p. 428
#1117 TOO FEW INNER CONTOUR FRAGMENTS IN THE BEAKER DESCRIPTION FILE. p. 428
#1124 THE BEAKER DESCRIPTION FILE CONTAINS TWO COINCIDING FRAGMENTS. A BOUNDARY FRAGMENT IS ONE OF THEM. p. 430
#1125 A DISCONTINUITY OF THE INNER CONTOUR IS FOUND IN THE BEAKER DESCRIPTION FILE. p. 430
#1126 A DISCONTINUITY OF THE OUTER CONTOUR IS FOUND IN THE BEAKER DESCRIPTION FILE. p. 430
#1127 THE BEAKER DESCRIPTION FILE CONTAINS INVALID DEFINITION OF MATERIALS AT A BOUNDARY FRAGMENT. p. 430
#1128 A BOUNDARY NODE IS EXPECTED BETWEEN TWO INNER CONTOUR FRAGMENTS WITH DIFFERENT MATERIAL DEFINITIONS. p. 430
#1129 A BOUNDARY NODE IS EXPECTED BETWEEN TWO OUTER FRAGMENTS OF THE BEAKER DESCRIPTION FILE. p. 430
#1144 DETECTOR IS BEHIND THE ABSORBER. p. 432
#1151 INVALID START-STOP ANGLES FOR THE INSIDE SOURCE. p. 432
#1152 INVALID START-STOP ANGLES FOR THE OUTSIDE SOURCE. p. 432
#1153 INVALID LENGTH OF THE INSIDE SOURCE. p. 432
#1154 INVALID LENGTH OF THE OUTSIDE SOURCE. p. 432
#1155 INSIDE SOURCE IS OUT OF TUBE. p. 432
#1203 SOURCE IS OUT OF U-CHANNEL. p. 434
#1204 INVALID LENGTH OF SOURCE IN THE U-CHANNEL TEMPLATE. p. 434
#1205 U-CHANNEL TOP WALL IS TOO THICK. p. 434
#1206 U-CHANNEL SIDE WALL IS TOO THICK. p. 434
#1207 ONE OR MORE OF THE U-CHANNEL OUTSIDE DIMENSIONS IS TOO SMALL. p. 434
#1251 TEMPLATE ORIENTATION PARAMETER FOR L-BEAM IS MISSING. p. 434
#1252 INVALID PARAMETER VALUE FOR L-BEAM TEMPLATE ORIENTATION. p. 434
#1253 SOURCE IS OUT OF L-BEAM. p. 434
#1305 H-BEAM CROSS-BAR IS TOO THICK. p. 436
#1306 H-BEAM SIDE WALL IS TOO THICK. p. 436
#1307 ONE OR MORE OF THE H-BEAM DIMENSIONS IS TOO SMALL. p. 436
#1351 SOURCE IS OUT OF RECTANGULAR TUBE. p. 436
#1352 INVALID LENGTH OF SOURCE IN THE RECTANGULAR TUBE TEMPLATE. p. 436
#1353 THE RECTANGULAR TUBE WALL IS TOO THICK. p. 436
#1354 ONE OR MORE OF THE RECTANGULAR TUBE DIMENSIONS IS TOO SMALL. p. 436
#1401 DETECTOR IS OUT OF ROOM THROUGH THE SURFACE. p. 436
#1402 ONE OR MORE OF THE ROOM DIMENSIONS IS TOO SMALL. p. 436
507 Invalid value of density p. 438
508 Internal error while attempting to insert the material p. 438
710 The number of template versions exceeds the maximum allowed p. 440
711 Invalid template version name p. 440
712 The template version name is already in use p. 440
713 Cannot open template version file p. 440
714 Cannot open the predefined beaker file p. 440
715 Invalid parameter in pre-defined beaker file p. 440
716 Not a valid contour ID p. 440
717 Invalid number of parameters (less than 4)! p. 440
718 Cannot load DLL with template information p. 440
719 Cannot get the address of a function in the template dll p. 440
720 New user template version may be based only on the default template version. p. 440
721 The material '%1' referenced in the geometry file is not available in the current mu-library. p. 440
722 The geometry definition contains the material '%1' which is not available in the current mu-library. p. 440
723 Density for the source material is missing p. 440
724 Cannot load .dll p. 440
725 Cannot get address of function in .dll p. 440
1037 Cannot open back-up copy of Space. (Space.bak). p. 444
1105 Filename of the Template DLL does not match its content. The file may have been renamed. p. 446
1123 Cannot get the address of a function in the template DLL. This is a system error. p. 448
1300 CANNOT FIND ECC_OUTPUT STATEMENT IN SPACE.INI FILE p. 448
1301 ENERGY LIST OF THIS FILE DOES NOT CORRESPOND TO THE LIST OF ALREADY LOADED FILE(S) p. 448
1302 INVALID CONTENT OF CURRENT ECC FILE. PLEASE, GENERATE THIS FILE AGAIN p. 448
1303 CAN NOT OPEN DESTINATION 'MULTIEFFICIENCY' DIRECTORY p. 448
1304 CAN NOT LOAD ECC FILE (SEE ROW MARKED BY RED) p. 448
1308 PLEASE CHECK VALUE OF 'WEIGHT'. ONLY FLOATING POINT NUMBER GREATER THAN ZERO IS ALLOWED. p. 448
1309 FILE WITH SAME NAME ALREADY EXITS. REPLACE? p. 448
1310 TOO LONG PARAMETER IN THE INPUT ECC LINE. THE INVALID PARAMETER IS SHOWN ON THE FOLLOWING LINE p. 448
1311 SAVE MULTI-EFFICIENCY RESULTS? p. 448

Codes and descriptions are taken from the manufacturer’s manual; page numbers link to the PDF. ManualLib is not affiliated with Canberra. Found a mistake? Report an error.