Mitsubishi Electric 600M Series Error Codes

407 codes from pages 466–506 of the manual

This is the list of error, alarm, warning codes the Mitsubishi Electric manual gives for the 600M Series CNC milling machine. Find your code below and open it for what the manual says about its causes and what to do.

Error codes from p. 466

CodeWhat it meansPage
SY0001 No main ladder p. 466
SY0002 User ladder code error p. 466
SY0003 S/W illegal interrupt p. 466
SY0004 S/W exceptional interrupt p. 466
SY0010 Watch dog p. 466
SY0020 SV initial communication error p. 466
SY0021 SV commu err: Ax No/type illegal p. 466
SY0022 SV commu err: CRC er/rcv incmp p. 466
SY0023 SV commu err: Recev frame No p. 466
SY0024 SV commu er sum: Ax No/type ilgl p. 466
SY0025 SV commu er sum: CRC er/rcv incmp p. 466
SY0026 SV commu er sum: Recev frame No p. 466
SY0030 Motor overheat p. 466
SY0031 Battery alarm p. 466
SY0032 Battery alarm detect circit err p. 466
SY0040 Initial parameter error p. 466
SV0010 Under voltage p. 467
SV0011 Axis selection error p. 467
SV0012 Memory error 1 p. 467
SV0013 S/W processing error p. 467
SV0016 Magnetic pole position detect err 1 p. 467
SV0017 AD converter error p. 467
SV0018 Initial communication error p. 467
SV001A Communication error (SUB) p. 467
SV001B CPU error (SUB) p. 467
SV001C LED error (SUB) p. 467
SV001D Data error (SUB) p. 467
SV001E Thermal error (SUB) p. 467
SV001F Communication error (SUB) p. 467
SV0020 No signal detection 1 p. 468
SV0021 No signal detection 2 p. 468
SV0022 LSI error p. 468
SV0024 Ground fault p. 468
SV0025 Absolute position lost p. 468
SV0026 Unused axis error p. 468
SV0027 Abs posn detect scale CPU err p. 468
SV0028 Absolute position overspeed p. 468
SV0029 Absolute posn detect circuit err p. 468
SV002A Relative posn detect circuit err p. 468
SV002B Scale CPU error p. 468
SV002C LED error p. 468
SV002D Data error p. 468
SV002F Communication error p. 468
SV0030 Over regeneration p. 468
SV0031 Overspeed p. 468
SV0032 Power module error p. 468
SV0033 Over voltage p. 468
SV0034 CRC error p. 468
SV0035 Data error p. 469
SV0036 Transferring error p. 469
SV0037 Initial parameter error p. 469
SV0038 Protocol error 1 (frame) p. 469
SV0039 Protocol error 2 (information) p. 469
SV003A Overcurrent p. 469
SV003B Power module error (overheat) p. 469
SV0042 Feedback error 1 p. 469
SV0043 Feedback error 2 p. 469
SV0046 Motor overheat p. 469
SV004F Instantaneous stop p. 469
SV0050 Overload 1 p. 469
SV0051 Overload 2 p. 469
SV0052 Excessive error1 p. 469
SV0053 Excessive error2 p. 469
SV0054 Excessive error3 p. 469
SV0055 EM p. 470
SV0058 CLT1 p. 470
SV0059 CLT2 p. 470
SV005A CLT3 p. 470
SV005F MCE p. 470
SV0061 POC p. 470
SV0063 PARE p. 470
SV0065 PRAE p. 470
SV0067 PPHL p. 470
SV0068 PWD p. 470
SV0069 PPNG p. 470
SV006A Pwr sply ext contactor fusion p. 470
SV006B Pwr sply rush relay fusion p. 470
SV006C PCH E p. 470
SV006E PME p. 470
SV006F PADE p. 470
SV0071 PINL p. 470
SV0073 Pwr sply over regeneration p. 470
SV0075 POV p. 470
SV0076 Pwr sply EMG stop setting err p. 470
SP0012 ME1 p. 472
SP0013 SWE p. 472
SP0017 ADE p. 472
SP0021 NS2 p. 472
SP0023 OSE p. 472
SP0031 OS p. 472
SP0032 PMOC p. 472
SP0034 DP p. 472
SP0035 DE p. 472
SP0036 TE p. 472
SP0037 PE p. 472
SP0038 TP1 p. 472
SP0039 TP2 p. 472
SP003B PMOH p. 472
SP0040 KE1 p. 472
SP0041 KE2 p. 472
SP0044 CAXE p. 472
SP0046 OHM p. 472
SP0050 OL p. 472
SP0052 OD p. 472
SP005C ORFE p. 473
SP0061 POC p. 473
SP0063 PARE p. 473
SP0065 PRAE p. 473
SP0067 PPHL p. 473
SP0068 PWD p. 473
SP0069 PPNG p. 473
SP006A Pwr sply ext contct fusion det p. 473
SP006B Pwr sply rush relay fusion det p. 473
SP006C PCH E p. 473
SP006E PME p. 473
SP006F PADE p. 473
SP0071 PINL p. 473
SP0073 Pwr sply over regeneration p. 473
SP0075 POV p. 473
SP0076 Pwr sply EMG stop setting err p. 473
SP0077 Pwr sply power module overheat p. 473
SP0088 WD p. 473
SP1001 AMP unequipped p. 473
SP1002 Illegal spindle amp p. 473
AX0021 Absolute position lost p. 474
AX0022 Abs posn tolerance amnt over p. 474
AX0024 Abs posn ref set incomplete p. 474
AX0051 Synchronous error excessive p. 474
AX0052 No synchronous CTRL spec p. 474
AX0101 H/W stroke end axis exists p. 474
AX0102 S/W stroke end axis exists p. 474
AX0103 Dog overrun p. 474
OP0101 Stroke end axis exists p. 476
OP0102 Stored stroke limit axis exists p. 476
OP0103 No. of spindle rot times over p. 476
OP0104 Verification error axis exists p. 476
OP0105 In axis control p. 476
OP0106 Emergency stop p. 476
OP0107 Program running p. 476
OP0108 Program checking p. 476
OP0109 No option spec p. 476
OP0110 Invalid Research after NURBS p. 476
OP0111 No NB number p. 476
OP0114 Restart from PRG TOP invalid p. 476
PR0001 Mode mismatch p. 477
PR0002 Search during auto operation p. 477
PR0003 Device invalid p. 477
PR0004 No file designation p. 477
PR0005 No file p. 477
PR0006 No N/B number p. 477
PR0010 No. of simultaneous axes over p. 477
PR0011 Illegal axis address p. 477
PR0020 Division error p. 477
PR0032 Illegal address p. 477
PR0033 Format error p. 477
PR0034 Illegal G code p. 477
PR0035 Address range over p. 477
PR0036 Program end error p. 477
PR0063 No high speed mode spec. p. 479
PR0070 Arc end point deviation large p. 479
PR0071 Can't calculate arc center p. 479
PR0072 No heirical spec. p. 479
PR0073 No scroll spec. p. 479
PR0080 No hypothetic axis spec. p. 479
PR0090 No thread cutting spec. p. 479
PR0093 Screw pitch err p. 479
PR0100 No cylinder interpolation spec. p. 479
PR0101 Cylinder mode error p. 479
PR0110 Plane selected during pattin rot p. 479
PR0111 Coord rotation plane selection p. 480
PR0112 Plane selected during R compen p. 480
PR0120 No synchronous feed spec. p. 480
PR0121 In F0 arc modal mode p. 480
PR0122 No auto corner override spec. p. 480
PR0124 No G93 spec. p. 480
PR0125 G93 mode error p. 480
PR0140 No t-pos offset p. 480
PR0141 T-pos during pat/cood rot p. 480
PR0142 T-pos offset G3 error p. 480
PR0150 No nose radius compensation p. 481
PR0151 Radius compen in arc modal p. 481
PR0152 No intersection p. 481
PR0153 Compensation interference p. 481
PR0154 No 3D-compensation spec. p. 481
PR0155 Fix cyc executed during compen p. 481
PR0164 No optional backward spec. p. 481
PR0170 No compensation number p. 481
PR0171 No G10 spec. p. 481
PR0172 G10 L-number error p. 481
PR0174 No G11 spec. p. 482
PR0180 No fixed cycle p. 482
PR0181 No spindle command (Tap cycle) p. 482
PR0182 Synchronous tap error p. 482
PR0183 No pitch/thread number p. 482
PR0184 Pitch/thread number error p. 482
PR0220 No special fixed cycle spec. p. 482
PR0221 No. of special fixed holes = 0 p. 482
PR0222 G36 angle interval error p. 482
PR0223 G12/G13 radius error p. 482
PR0224 No G12/G13 spec. p. 482
PR0230 Sub-program nesting over p. 482
PR0231 No N-Number p. 482
PR0232 No program No. p. 482
PR0240 No variable command p. 482
PR0241 No variable number p. 482
PR0280 ['' and '' nesting over p. 484
PR0281 Number of ['' and ''] differ p. 484
PR0282 Can't calculate p. 484
PR0283 Zero division p. 484
PR0284 Overflow value p. 484
PR0285 Float value overflow p. 484
PR0290 IF statement error p. 484
PR0291 WHILE statement error p. 484
PR0292 SETVN statement error p. 484
PR0293 DO-END nesting over p. 484
PR0294 DO and END not in proper pairs p. 484
PR0295 Tape WHILE/ GOTO p. 484
PR0300 Variable name illegal p. 484
PR0301 Variable name duplicated p. 484
PR0350 No scaling spec. p. 484
PR0396 Plane selected in GEOMT ctrl p. 486
PR0420 No parameter input spec. p. 486
PR0421 Parameter input error p. 486
PR0430 Return incomplete axis exists p. 486
PR0431 No 2nd 3rd 4th ref-p ret spec. p. 486
PR0435 G27 and M commands in same block p. 486
PR0436 G29 and M commands in same block p. 486
PR0437 No. G54.1 spec. p. 486
PR0438 Local coord set during exp wk co p. 486
PR0451 No check-before-move spec. p. 486
PR0452 Movement limit p. 487
PR0460 Tape I/O error p. 487
PR0461 File I/O p. 487
PR0462 Computer Link error p. 487
PR0463 Read forced quit p. 487
PR0470 No Computer Link A p. 487
PR0471 No Computer Link B p. 487
PR0490 No disk operation p. 487
PR0491 No FLD operation p. 487
PR0492 No IC card operation p. 487
PR0493 No dataserver operation p. 487
PR0600 No auto TLM p. 487
PR0601 No skip p. 488
PR0602 No multi skip p. 488
PR0603 Skip speed 0 p. 488
PR0604 G37 illegal axis p. 488
PR0605 H and G37 commands in same block p. 488
PR0606 H command not found before G37 p. 488
PR0607 Signal turned illegally with G37 p. 488
PR0608 Skip during radius compen p. 488
PR0611 No hi-precis (G61.1) spec. p. 488
PR0612 No hi-precis die (G61.2/3) spec. p. 488
PR0615 No hi-precis part (G61.5) spec. p. 488
PR0621 NURBS knot error p. 488
PR0622 NURBS weight error p. 488
PR0623 NURBS degree error p. 488
PR0624 NURBS control point error p. 488
PR0625 NURBS misc error p. 489
PR0626 No NURBS spec. p. 489
PR0900 No normal control p. 489
PR0901 G92 command on normal axis p. 489
PR0902 Normal axis set as linear axis p. 489
PR0903 At block joint turn angle over p. 489
PR0920 No 3DIM coord conversion spec. p. 489
PR0921 3DIM coord convert error p. 489
PR0922 Illegal 3DIM coord convert p. 489
PR0990 Illegal process p. 489
AY0020 Aux axis initial communication error p. 495
AY0021 Aux axis commu err: Ax No/type illegal p. 495
AY0022 Aux axis commu err: CRC er/rcv incmp p. 495
AY0023 Aux axis commu err: Recev frame No p. 495
AY0024 Aux axis commu er sum: Ax No/type ilgl p. 495
AY0025 Aux axis commu er sum: CRC er/rcv incmp p. 495
AY0026 Aux axis commu er sum: Recev frame No p. 495
SYW0001 External switch emergency stop p. 496
SYW0002 RIO1 communication error p. 496
SYW0003 RIO2 communication error p. 496
SYW0004 RIO3 communication error p. 496
SYW0005 PLC emergency stop p. 496
SYW0006 PLC signal p. 496
SYW0007 EMG stop: SV commu. stop p. 496
SYW0008 Ext board EMG stop: SV end off p. 496
SYW0009 RIO4 communication error p. 496
SYW0040 The others EMG p. 496
SYW0050 Low battery voltage p. 496
SYW0060 PLC-H timer over p. 497
SYW0070 Receive result of diagnosis p. 497
SYW0071 Modem initial error p. 497
SYW0072 Redial over p. 497
SYW0073 No dial tone p. 497
SYW0074 Network error p. 497
SYW0999 Tool double registration p. 497
SVW0090 Low-speed communication err p. 498
SVW0091 Communication error p. 498
SVW0092 Serial format error p. 498
SVW0093 Absolute position dislocation p. 498
SVW0096 MP scale feedback error p. 498
SVW0097 MP scale offset error p. 498
SVW009E High-speed rotary counter err p. 498
SVW009F Low battery voltage p. 498
SVW00E0 Over regeneration warning p. 498
SVW00E1 Overload warning p. 498
SVW00E3 Abs position counter warning p. 498
SVW00E4 Parameter error warning p. 498
SVW00E7 NC emergency stop p. 498
SVW00E8 Aux regeneration frequency over p. 498
SVW00E9 Instantaneous stop warning p. 498
SVW00EA External emergency stop p. 498
SVW00EB Over regeneration warning p. 498
OPW0165 Chopping rot axis invalid p. 504
OPW0166 Invalid Ope in NURBS mode p. 504
OPW0167 F1 Feed Rate Zero p. 504
OPW0168 Ref.pnt ret cancel tool offset p. 504
OPW0169 Rotate work compen excessive p. 504
OPW0170 External deceleration axis p. 504

Alarm codes from p. 478

CodeWhat it meansPage
PR0037 Label and N number zero p. 478
PR0038 No additional Op block skip p. 478
PR0039 No EOB p. 478
PR0040 Unused address exists p. 478
PR0041 Overlap G code exists p. 478
PR0042 Meaningless H code p. 478
PR0043 No end point operation in arc p. 478
PR0050 No inch/mm spec. p. 478
PR0060 Compensation length over p. 478
PR0061 No 1-direction positioning spec. p. 478
PR0062 No F command p. 478
PR0242 Variable definition = none p. 483
PR0243 Can't use variables p. 483
PR0244 No. of var definitions over p. 483
PR0250 No pattern rotation p. 483
PR0251 Pattern rotation duplicated p. 483
PR0252 Pattern and coord rotation p. 483
PR0260 No coordinates rotation p. 483
PR0270 No user macro p. 483
PR0271 No macro interrupt p. 483
PR0272 NC text/macro text simultaneous p. 483
PR0273 Macro call nesting over p. 483
PR0275 Variable number illegal p. 483
PR0276 Macro call cancel independent p. 483
PR0277 Macro alarm message p. 483
PR0360 No program mirror spec. p. 485
PR0380 No corner R/C spec. p. 485
PR0382 No corner movement p. 485
PR0383 Corner movement short p. 485
PR0384 Corner next movement short p. 485
PR0385 Corner during G0/G33 p. 485
PR0386 Can't execute corner R (C) p. 485
PR0390 No geometric spec. p. 485
PR0391 No geometric arc spec. p. 485
PR0392 Angle less than 1 deg (GEOMT) p. 485
PR0393 Inc value in 2nd block (GEOMT) p. 485
PR0394 No linear move command (GEOMT) p. 485
PR0395 Illegal address (GEOMT) p. 485
OPW0123 Machining time calculate mode p. 502
OPW0124 In synchronous correction mode p. 502
OPW0125 In axis control p. 502
OPW0126 Acc/dec T cnst pre-intpl large p. 502
OPW0127 In emergency stop p. 502
OPW0128 In absolute position alarm p. 502
OPW0129 In abs posn initial setting p. 502
OPW0130 Tool life over p. 502
OPW0131 Overheat p. 502
OPW0132 Top search not completed p. 502
OPW0133 Restart search error p. 502

Warning codes from p. 499

CodeWhat it meansPage
SPW00E1 Overload warning p. 499
SPW00E4 Parameter error warning p. 499
SPW00E7 NC emergency stop p. 499
SPW00E8 Aux regeneration frequency over p. 499
SPW00E9 Instantaneous stop warning p. 499
SPW00EA External emergency stop p. 499
SPW00EB Over regeneration warning p. 499
OPW0101 Auto operation pause signal ON p. 500
OPW0102 Single block stop signal ON p. 500
OPW0104 External interlock axis exists p. 500
OPW0106 Operation mode change p. 500
OPW0107 No operation mode p. 500
OPW0108 Operation mode duplicated p. 500
OPW0109 Cutting override zero p. 500
OPW0110 Rapid feed override zero p. 500
OPW0111 External feedrate zero p. 501
OPW0112 Spindle stop p. 501
OPW0113 Block start interlock p. 501
OPW0114 Cutting block start interlock p. 501
OPW0115 Restart switch ON p. 501
OPW0116 Prog restart posn not searched p. 501
OPW0117 Prog restart posn not returned p. 501
OPW0118 No MDI setting p. 501
OPW0119 In program search p. 501
OPW0120 Program check mode p. 501
OPW0121 In buffer correction p. 501
OPW0122 In reset process p. 501
PRW0001 Overlap address exists p. 505
PRW0002 Overlap G code exists p. 505
PRW0003 Ignored G code exists p. 505
PRW0004 Unused address exists p. 505
PRW0005 Ref point ret in pattern rot p. 505
PRW0006 No end point operation in arc p. 505
PRW0007 Cylinder mode warning p. 505
ASW0052 Aux axis servo warning p. 506
0092 Battery voltage drop p. 506
00E0 Over-regeneration warning p. 506
00E1 Overload warning p. 506
00E3 Absolute position counter warning p. 506
00E9 Main circuit OFF warning p. 506
AZW0073 Aux axis system warning p. 506
0001 Absolute position memory battery voltage warning p. 506
0003 Absolute position counter warning p. 506

Codes and descriptions are taken from the manufacturer’s manual; page numbers link to the PDF. ManualLib is not affiliated with Mitsubishi Electric. Found a mistake? Report an error.