Mitsubishi Electric MDS-C1 Series Error Codes

111 codes from pages 296–349 of the manual

This is the list of alarm, error, warning codes the Mitsubishi Electric manual gives for the MDS-C1 Series AC Servo/Spindle. Find your code below and open it for what the manual says about its causes and what to do.

Alarm codes from p. 296

Error codes from p. 309

CodeWhat it meansPage
11 Axis selection error p. 309
12 Memory error 1 p. 309
13 Software processing error 1 p. 309
14 Software processing error 2 p. 309
16 Magnetic pole position detection error p. 309
17 A/D converter error p. 309
18 Motor side detector, initial communication error p. 309
19 Synchronous control/detector communication error p. 309
1A Machine side detector, initial communication error p. 309
1B Machine side detector, CPU error 1 p. 309
1C Machine side detector, EEPROM/LED abnormality p. 309
1D Machine side detector, data error p. 309
1E Machine side detector, memory error p. 309
1F Machine side detector, communication error p. 309
20 Motor side detector, No signal 1 p. 310
21 Machine side detector, No signal 2 p. 310
23 Excessive speed deflection 1 p. 310
25 Absolute position lost p. 310
26 Unusable axis error p. 310
27 Machine side detector, CPU error 2 p. 310
28 Machine side detector, overspeed p. 310
29 Machine side detector, absolute position data error p. 310
2A Machine side detector, incremental position data error p. 310
2B Motor side detector, CPU error 1 p. 310
2C Motor side detector, EEPROM/LED error p. 310
2D Motor side detector, data error p. 310
2F Motor side detector, communication error p. 310
31 Overspeed p. 310
32 Power module overcurrent p. 310
34 Communication or CRC error between NC and drive unit p. 310
35 NC command error p. 310
36 Communication or transmission error between NC and drive unit p. 310
37 Initial parameter error p. 310
38 Communication or protocol error 1 between NC and drive unit p. 310
39 Communication or protocol error 2 between NC and drive unit p. 310
3A Overcurrent p. 310
3B Power module overheate p. 310
3D Spindle speed lock p. 310
3E Spindle speed overrun p. 310
3F Speed excessive deflection 2 p. 310
40 Detector changeover unit, changeover error p. 311
41 Detector changeover unit, communication error p. 311
42 Feedback error 1 p. 311
43 Feedback error 2 p. 311
44 C-axis changeover alarm p. 311
46 Motor overheat p. 311
4E NC command mode error p. 311
50 Overload 1 p. 311
51 Overload 2 p. 311
52 Excessive error 1 p. 311
53 Excessive error 2 p. 311
54 Excessive error 3 p. 311
58 Collision detection 1 G0 p. 311
59 Collision detection 1 G1 p. 311
5A Collision detection 2 p. 311
5C Orientation feedback error p. 311
60 Instantaneous power failure p. 312
61 Power module overcurrent p. 312
62 Frequency error p. 312
63 Auxiliary regeneration error p. 312
65 Rush relay error p. 312
67 Phase failure p. 312
68 Watch dog p. 312
69 Ground fault p. 312
6A External contactor melting p. 312
6B Rush relay melted p. 312
6C Main circuit error p. 312
6D Parameter error p. 312
6E Memory error p. 312
6F Power supply error p. 312
71 Instantaneous power failure/external emergency stop p. 312
73 Over-regeneration p. 312
74 Regenerative resistor overheating p. 312
75 Overvoltage p. 312
76 External emergency stop setting error p. 312
77 Power module overheating p. 312
7F Power reboot request p. 313
89 Detector converter unit 2 connection error p. 313
8A Encoder converter unit 2 communication error p. 313
8B Encoder converter unit 2 automatic adjustment error p. 313
8C Encoder converter unit 2 judgment error p. 313
8D Encoder converter unit 2 CPU error p. 313
8E Encoder converter unit 2 data error p. 313
2269 The CNC setting maximum rapid traverse rate value is incorrect. The CNC system software may be illegal. p. 349
2271 The CNC setting maximum cutting speed setting value is incorrect. The CNC system software may be illegal. p. 349
2301 The following settings are overflowing p. 349
2302 The absolute position parameter is valid when OSE104 and OSE105 are connected. p. 349
2303 The servo option is not available. The closed loop or dual feedback control function is set. p. 349
2304 The servo option is not available. The SHG control function is set p. 349
2305 The servo option is not available. The adaptive filter function is set. p. 349
2306 The servo option is not available. The MP scale absolute position function is set. p. 349
2308 The valid/invalid setting of the 4th or 5th notch filter is changed from the initial setting. p. 349

Warning codes from p. 314

Codes and descriptions are taken from the manufacturer’s manual; page numbers link to the PDF. ManualLib is not affiliated with Mitsubishi Electric. Found a mistake? Report an error.