Industrial

This document describes the features and characteristics of HIT667, which is a low frequency power amplifier and complementary pair with HIT647.

The HI-8382 and HI-8383 are silicon gate CMOS devices designed as a line driver in accordance with the ARINC 429 bus specifications. Inputs are provided for clocking and synchronization. These signals are AND'd with the DATA inputs to enhance system performance and allow the HI-8382 to be used in a variety of applications. Both logic and synchronization inputs feature built-in 2,000V minimum ESD input protection as well as TTL and CMOS compatibility. The differential outputs of the HI-8382 are independently programmable to either the high speed or low speed ARINC 429 output rise and fall time specifications through the use of two external capacitors. The output voltage swing is also adjustable by the application of an external voltage to the VREF input. The HI-8382 has on-chip Zener diodes in series with a fuse to each differential output protecting the ARINC bus from an overvoltage failure. The outputs each have a series resistance of 37.5 ohms. The HI-8383 is identical to the HI- 8382 except that the series resistors are 13 ohms and the overvoltage protection circuitry has been eliminated. The updated HI-318X and HI-8585 ARINC 429 line drivers are recommended for all new designs where logic signals must be converted to ARINC 429 levels such as a user ASIC, the HI-3282 or HI-8282A ARINC 429 Serial Transmitter/Dual Receiver, the HI-6010 ARINC 429 Transmitter/Receiver or the HI-8783 ARINC interface device. Holt products are readily available.

The HI-5040 series CMOS analog switches offer low resistance switching performance for analog voltages up to the supply rails and for signal currents up to 80mA.

The HD74HCT563/HD74HCT573 are octal transparent latches with 3-state outputs. When the latch enable (LE) input is high, the Q outputs of the HD74HCT563 will follow the inversion of the D inputs, while the Q outputs of the HD74HCT573 will follow the D inputs. When the latch enable goes low, data at the D inputs will be retained at the outputs until latch enabled returns high again. When a high logic level is applied to the output control input, all outputs go to a high impedance state, regardless of what signals are present at the other inputs and the state of the storage elements.

This document contains information about HD14075, including dimensions, weight, and compatibility.

This document provides specifications for HD14068, including dimensions, weight, and technical requirements.

The HCF4009UB is a monolithic integrated circuit fabricated in Metal Oxide Semiconductor technology. It can be used as CMOS to TTL or DTL logic level converters, as current 'sink' or 'source' drivers, or as a multiplexer (1 to 6). It is a preferred replacement of HCF4049UB in buffer applications.

Current transducers HAZ 4000..20000-SRI are for the electronic measurement of currents: DC, AC, pulsed, mixed, with a galvanic isolation between the primary circuit (high power) and the secondary.

The HA-A1370/A1380 Series of quartz crystal oscillators provide enable/disable 3-state CMOS compatible signals for bus connected systems. These oscillators operate at a supply voltage of 3.3 Volts and have a wide frequency range of 0.5MHz to 20.0MHz. User specified tolerances are available. The HA-A1370/A1380 Series is designed to withstand vapor phase temperatures of 253°C for 4 minutes maximum. These oscillators are packaged in an all metal, resistance weld, hermetically sealed package.

This file provides the specifications for JEWEL HILL ELECTRONIC CO.,LTD.'s GT2030 LCD module.

The GS-R24P series is a family of high efficiency step down switching voltage regulators, designed to replace linear regulators. It has a MTBF of 1,000,000 hours (Tamb=25°C), maximum output current of 1.5A, maximum input voltage of 35V, maximum drop-out voltage of 1.5V, remote logic inhibit/enable feature, non-latching overload and short circuit protection, thermal shutdown, fixed or adjustable output, and no heatsink required.

The GS-DC200 series is a family of single Eurocard boards that contain all the logic necessary to operate a stepper motor, including the instructions decoding, the step timing generation, the storage of the program to be executed. The motor interface can deliver phase current up to 2.5A. The boards can be used as a stand alone complete motion control system or they can be driven by a central host computer. The GS-DC200 family isbuilt around the GS-C200, GS-C200S, GS-D200, GS-D200S modules, (see the relevant data sheet) and it retains all the features of these modules.

The GS9090 is a 270Mb/s reclocking deserializer with an internal FIFO. When used in conjunction with one of Gennum’s SDI Cable Equalizers, a receive solution for SD-SDI and DVB-ASI applications can be realized.

GS88237AB is a 9Mb synchronous burst SRAM with high performance and low power consumption. It supports single/dual cycle deselect and features IEEE 1149.1 JTAG-compatible boundary scan. The product is suitable for level 2 cache applications supporting high performance CPUs, as well as synchronous SRAM applications such as DSP main store and networking chip set support.