Industrial

ITT Cannon 1.6/5.6 RF coaxial connectors are suitable for use in 75 ohm communication systems

M36W832TE, M36W832BE are 32 Mbit (2 Mb x16, Boot Block) Flash Memory and 8 Mbit (512Kb x16) SRAM, Multiple Memory Product.

The Samsung M366S1723DTS PC133/PC100 Unbuffered DIMM is a 16M bit x 64 Synchronous Dynamic RAM high density memory module.

This document introduces the features and characteristics of M29W320DT/DB products, including supply voltage, access time, programming time, storage blocks, programming/erase controllers, erase suspend and resume modes, unlock bypass programming command, VPP/WP pins, temporary block unprotected mode, common flash interface, low power consumption, and 100,000 programming/erase cycles

This document describes the features and characteristics of the M29F016B 16 Mbit (2Mb x8, Uniform Block) Single Supply Flash Memory, including single supply voltage, access time, programming time, memory blocks, program/erase controller, erase suspend and resume modes, temporary block unprotection mode, unlock bypass program command, low power consumption, lifetime, electronic signature, etc.

2 Mbit (256Kb x8, Boot Block) Single Supply Flash Memory I SINGLE 5V ± 10% SUPPLY VOLTAGE for PROGRAM, ERASE and READ OPERATIONS I ACCESS TIME: 45 ns I PROGRAMMING TIME – 8 µs by Byte typical I 7 MEMORY BLOCKS – 1 Boot Block (Top or Bottom Location) – 2 Parameter and 4 Main Blocks I PROGRAM/ERASE CONTROLLER – Embedded Byte Program algorithm – Embedded Multi-Block/Chip Erase algorithm – Status Register Polling and Toggle Bits I ERASE SUSPEND and RESUME MODES – Read and Program another Block during Erase Suspend I UNLOCK BYPASS PROGRAM COMMAND – Faster Production/Batch Programming I TEMPORARY BLOCK UNPROTECTION MODE I LOW POWER CONSUMPTION – Standby and Automatic Standby I 100,000 PROGRAM/ERASE CYCLES per BLOCK I 20 YEARS DATA RETENTION – Defectivity below 1 ppm/year I ELECTRONIC SIGNATURE – Manufacturer Code: 20h – Top Device Code M29F002BT: B0h – Top Device Code M29F002BNT: B0h – Bottom Device Code M29F002BB: 34h – Bottom Device Code M29F002BNB: 34h

M29F160BT and M29F160BB are two single-supply flash memories that can be programmed, erased, and read at a 5V ±10% voltage. They have a 55ns access time, an 8µs per byte/word programming time, 35 memory blocks (1 boot block (top or bottom location) and 2 parameters and 32 main blocks), an embedded byte/word program algorithm, an embedded multi-block/chip erase algorithm, status register polling and toggle bits, a ready/busy output pin, erase suspend and resume modes, reading and programming another block during erase suspend, unlock bypass program command, faster production/batch programming, temporary block unprotection mode, standby and automatic standby, 100,000 block program/erase cycles, 20 years data retention (defectivity below 1 ppm/year), and an electronic signature (manufacturer code: 0020h, top device code M29F160BT: 22CCh, bottom device code M29F160BB: 224Bh).

M27C801 is an 8 Mbit UV EPROM and OTP EPROM with a supply voltage of 5V ± 10% and an access time of 45ns in read operation. It features low power consumption, programming voltage of 12.75V ± 0.25V, programming time of 50µs/word, etc.

M27C4001 is a 4 Mbit EPROM offered in the two ranges UV (ultra violet erase) and OTP (one time programmable).

LTC2404/LTC2408 4-/8-channel 24-bit µPower No Latency ∆ΣTM ADCs with integrated oscillator, 4ppm INL and 0.3ppm RMS noise. They use delta-sigma technology and provide single cycle digital filter settling time (no latency delay) for multiplexed applications. The first conversion after the channel is changed is always valid. Through a single pin the LTC2404/ LTC2408 can be configured for better than 110dB rejec- tion at 50Hz or 60Hz ±2%, or can be driven by an external oscillator for a user defined rejection frequency in the range 1Hz to 120Hz. The internal oscillator requires no external frequency setting components. The converters accept any external reference voltage from 0.1V to VCC. With their extended input conversion range of –12.5% VREF to 112.5% VREF the LTC2404/LTC2408 smoothly resolve the offset and overrange problems of preceding sensors or signal conditioning circuits. The LTC2404/LTC2408 communicate through a flexible 4-wire digital interface which is compatible with SPI and MICROWIRE TM protocols.

This datasheet provides detailed information about LTC2293/LTC2292/LTC2291, including features, applications, typical applications, specifications, and packages.

The LTC1562-2 is a low noise, low distortion continuous time filter with rail-to-rail inputs and outputs, optimized for a center frequency (fO) of 20kHz to 300kHz. It does not require a clock signal. The filter consists of four independent 2nd order filter blocks that can be cascaded in any combination, such as one 8th order or two 4th order filters. The response of each block can be programmed with three external resistors to set the center frequency, Q, and gain using simple design formulas. Each 2nd order block provides lowpass and bandpass outputs. Highpass response is available if an external capacitor replaces one of the resistors. Allpass, notch, and elliptic responses can also be realized. The LTC1562-2 is designed for applications where dynamic range is important. For example, by cascading 2nd order sections in pairs, the user can configure the IC as a dual 4th order Butterworth lowpass filter with a 90dB signal-to-noise ratio from a single 5V power supply. Low level signals can exploit the built-in gain capability of the LTC1562-2. Varying the gain of a section can achieve a dynamic range as high as 114dB with a ±5V supply. Other cutoff frequency ranges can be provided upon request. Please contact LTC Marketing. LTC, LT are registered trademarks of Linear Technology Corporation.

The LT1579 is a dual input, single output, low dropout regulator designed to provide an uninterruptible output voltage from two independent input voltage sources on a priority basis. All of the circuitry needed to switch smoothly and automatically between inputs is incorporated. The LT1579 can supply 300mA of output current from either input at a dropout voltage of 0.4V. Quiescent current is 50µA, dropping to 7µA in shutdown. Two comparators are included to monitor input voltage status. Two additional status flags indicate which input is supplying power and provide an early warning against loss of output regulation when both inputs are low. A secondary select pin is provided so that the user can force the device to switch from the primary input to the secondary input. Internal protection circuitry includes reverse-battery protection, current limiting, thermal limiting and reverse-current protection. The device is available in fixed output voltages of 3V, 3.3V and 5V, and as an adjustable device with a 1.5V reference voltage. The LT1579 regulators are available in narrow 16-lead SO and 16-lead SSOP packages with all features, and in SO-8 with limited features.

The LP38690/2-ADJ low dropout CMOS linear regulators provide 2.5% precision reference voltage, extremely low dropout voltage (450mV @ 1A load current, VOUT = 5V) and excellent AC performance utilizing ultra low ESR ceramic output capacitors.

LOC110 is a linear optocoupler from Clare company, which can be used in telecom, medical and power supply isolation circuits. It has 8-pin DIP, surface mount or flat pack packages available.