GSK GSK980TB3 Error Codes

105 codes from pages 265–272 of the manual

This is the list of alarm codes the GSK manual gives for the GSK980TB3 GSK GSK980TB3. Find your code below and open it for what the manual says about its causes and what to do.

Alarm codes from p. 265

CodeWhat it meansPage
022 is no zero or zero point is at the edge of the block. p. 265
023 When circular interpolation defined by radius R is used, R defined a negative value. p. 265
024 Radius of circular interpolation is too big p. 265
026 The value specified in circular interpolation can not form a circular arc. p. 265
027 In circular interpolation, R and (K,I) are specified simultaneously p. 265
028 In circular interpolation, R and (K,I) are zero p. 265
029 The offset value specified by T code is too big p. 265
030 Tool offset number exceeds the range p. 265
031 The file can not be found p. 265
032 Communication error p. 265
033 There is no cross point in tool nose radius compensation p. 265
034 G2 or G3 is executed when starting or canceling the tool radius compensation. p. 265
035 Compensation direction of the next block changes after the compensation is started. p. 265
036 Tool radius compensation is performed before tool offset number is specified. p. 265
037 Block is non-moving G Code when compensation starts. p. 265
038 In tool nose radius compensation, excessive cutting occurs as starting point or terminal point of the circular arc coincides with the center point, p. 265
039 30 non-moving G Codes appear continuously in the process of tool compensation. p. 265
040 Illegal command appears in the process of tool compensation p. 265
041 Excessive cutting will occur in tool nose radius compensation p. 265
042 In the process of tool nose radius compensation, G code is specified repeatedly in circular arc command. p. 265
043 Data input exceeds the allowable range p. 265
044 Spindle disabled if chuck is not clamped. p. 267
045 Chuck unclamping is not allowed when spindle is in operation. p. 267
046 Storage is wrong at power off. Please power on the CNC. p. 267
047 Spindle CW (rotates negatively) is specified before stopping spindle CCW (rotates positively). p. 267
050 An unusable tool nose angle is specified in G76. p. 267
051 In G76, minimum specified cutting depth or finishing allowance is bigger than thread height. p. 267
052 Thread height or initial cutting depth specified in G76, which is 0 or negative number. p. 267
053 P or Q value is not specified in G70,G71,G72,G73 code. p. 267
054 #I or #K in G74 or G75 is a negative value. p. 267
055 G76 finishing allowance is a negative value. p. 267
062 (1) Cutting depth in G71 or G72 is 0 or negative value. (2) G73 repetition time is 0 or negative value (3) D-i or D-k command in G74 or G75 is negative value (4) While D-i or D-k command in G74 or G75 is not 0, address U or W is specified as 0 or negative value (5) While tool retraction direction of G74 or G75 is specified, D-d is a negative number. p. 267
063 In G70, blocks specified by P or Q can not be found p. 267
064 Tool compensation is not cancelled when G code is G32,G33,G90~G94,G70~G76. p. 267
065 (1) In code G71,G72 or G73, in the block whose sequence number is specified by address P, G00 or G01 is not defined. (2) In code G71 or G72, in the block whose sequence number is specified by address P, address Z(W)(G71) or X(U)(G72) are defined. p. 267
066 In code G70, G71,G72,G73, in the blocks specified by P or Q, non-moving G Code or unusable G code is specified. p. 267
067 M98,M99 or M30.is specified in the blocks that is specified by address P or Q. p. 267
068 P or Q value of G70 is specified repeatedly. p. 267
074 The program number is out of the range of 0001-9999 p. 268
076 In the block M98, P is not specified p. 268
077 Subprogram calls too many nests p. 268
078 The specified program number or sequence number has not been found in subprogram call. p. 268
079 Macro code alarm does not exist p. 268
081 NC program and customer macro program exist simultaneously p. 268
100 Parameter switch is ON p. 268
101 In program editing, power is off. Please edit the program again p. 268
102 The number of lines exceed the maximum value p. 268
103 Memory data of parameter, tool compensation and coordinate are initialized. p. 268
104 Because CNC abnormality is detected, it needs to check parameter again. p. 268
105 It detects data of tool length compensation is abnormal. Please set the tool again. p. 268
106 It detects data of the absolute data is abnormal. Please set tool again. p. 268
107 It defects the drive, spindle etc. are changing p. 268
110 When copied and renamed, the program name already exists p. 268
114 In G65 block, undefined H code is specified p. 268
115 Illegal variable number is specified p. 268
128 When transferring the command, the sequence number of address to be transferred is not in the allowable range, or it is not found. p. 268
129 A block must not contain identical function words or same series of G code. p. 268
130 The value of the address exceeds the range p. 268
131 Group G00 and group G01 must not appear at the same time p. 268
162 P is non-integral value or a negative value in the blocks of the called program. p. 270
163 Subprogram is called too many times p. 270
164 Exceed the maximum storage number (500) p. 270
165 The sentence for calling subprogram or returning subprogram is in illegal block (G90-G94, G70~G76). p. 270
166 Pno and Qno values assigned by G70, G71, G72, and G73 exceed the range or they are non-integral. p. 270
168 P,U and X in the pause command can not be specified at the same time p. 270
169 Q and R in macro program are specified incorrectly p. 270
170 Please input correct password in setting interface before modifying parameter and screw pitch compensation data. p. 270
171 Spindle enable signal is not received p. 270
180 M41~M44 can not be used when spindle is in gear control or spindle automatic gearing is inactive. p. 270
181 M code is wrong. Illegal M code is edited in the program p. 270
182 S code is wrong. Illegal S code is edited in the program p. 270
183 T code is wrong. Illegal T code is edited in the program p. 270
185 Time for tool setting is too long. Specified tool arrival signal has not been received Ta time after the start of tool CCW rotation. Alarm occurs. p. 270
186 Tool post CW rotation locking signal is not received in the time of tool post CW rotation locking time. p. 270
187 Tool changing is not ready. Tool number is not consistent with the current tool number. p. 270
188 M45~M49 commands are executed while corresponding in-position input signal is not received. p. 270
189 Chuck in-position signal is not received within the stipulated time. p. 271
190 Axis number is changed, and data initialization is successful. p. 271
191 Key pressing is overtime. p. 271
193 Please pull out U-disk! p. 271
201 Exceed X-axis positive stroke limit. p. 271
202 Exceed X-axis negative stroke limit. p. 271
203 Exceed X-axis positive stroke limit. p. 271
204 Exceed Z-axis negative stroke limit. p. 271
205 Exceed Y-axis positive stroke limit. p. 271
206 Exceed Y-axis negative stroke limit. p. 271
207 X-axis hardware overtravel (negative). p. 271
208 Z-axis hardware overtravel (negative). p. 271
209 X-axis hardware overtravel (positive). p. 271
210 Z-axis hardware overtravel (positive). p. 271
211 X-axis drive unit is not ready. p. 271
212 Z-axis drive unit is not ready. p. 271
213 X/Z -axis drive unit is not ready. p. 271
221 X-axis drive unit alarm. p. 271
222 Z-axis drive unit alarm. p. 271
223 X-axis overtravel alarm. p. 271
224 Z-axis overtravel alarm. p. 271
250 Tailstock advance/retract can not be performed in Auto mode or after the spindle is started. p. 271
251 External alarm 1. p. 271
252 External alarm 2. p. 272
253 Pressure is too low. p. 272
254 Preparation is not ready. p. 272
255 Safety door is open in automatic operation. p. 272
258 IO port setting is wrong. p. 272
259 Timer has faults. p. 272

Codes and descriptions are taken from the manufacturer’s manual; page numbers link to the PDF. ManualLib is not affiliated with GSK. Found a mistake? Report an error.