Philips manuals, page 35
PHILIPS 74F808 74F1808 handbook
This document describes the features of the 74F808 and 74F1808 Hex 2-input AND drivers. These drivers have high capacitive drive capability, a typical propagation delay of 4.0ns, superior ground noise characteristics, and increased source and sink current.
PHILIPS 74F805 74F1805 handbook
74F805/74F1805 is a Hex 2-input NOR driver launched by Philips Semiconductors. The product has high capacitive drive capability and can be configured in Corner VCC and GND or Center VCC and GND. The typical propagation delay is 2.3ns.
PHILIPS 74F804 74F1804 handbook
74F804/1804 is a 2-input NAND driver with high capacitive drive capability produced by Philips Semiconductors. It has a typical propagation delay of 2.5ns and a typical supply current of 9mA.
PHILIPS 74F1779 handbook
PHILIPS 74F1763 handbook
This document describes the features and functions of the Philips Semiconductors 74F1763 Intelligent DRAM Controller (IDC), including DRAM signal timing generator, automatic refresh circuitry, selectable row address hold and RAS precharge times, etc. The controller is designed for controlling 1 MBit DRAMs and supports intelligent burst-mode refresh after page-mode access cycles. The document also introduces some improved features of the product, such as page-mode access, selectable RAS precharge time, and row-address hold time to fit different DRAMs.
PHILIPS 74F174 handbook
The 74F174 is a hex D-type flip-flop with individual D inputs and Q outputs, produced by Philips Semiconductors. The common buffered Clock (CP) and Master Reset (MR) inputs load and reset (clear) all flip-flops simultaneously. The register is fully edge-triggered. The state of each D input, one setup time before the Low-to-High clock transition is transferred to the corresponding flip-flop’s Q output. All Q outputs will be forced Low independent of Clock or Data inputs by a Low voltage level on the MR input. The device is useful for applications where true outputs only are required, and the Clock and Master Reset are common to all storage elements.
PHILIPS 74F173 handbook
The 74F173 is a high speed 4-bit parallel load register with clock enable control, 3-state buffered outputs, and master reset (MR) function
PHILIPS 74F169 handbook
The document describes the features and characteristics of the 74F169 4-bit up/down binary synchronous counter, including synchronous counting and loading, up/down counting, modulo 16 binary counter, two count enable inputs for n-bit cascading, positive edge-triggered clock, built-in carry look-ahead capability, and presettable for programmable operation.
PHILIPS 74F1604 handbook
This document is the product specification for the 74F1604 Latch from Philips Semiconductors. The product features high impedance NPN base inputs, 16-bit wide data inputs, and multiplexed 8-bit outputs.
PHILIPS 74F154 handbook
This document describes the features and characteristics of the 74F154 decoder/demultiplexer, including its 16-line demultiplexing capability, mutually exclusive outputs, and 2-input enable gate for strobing or expansion. The decoder accepts four active High binary address inputs and provides 16 mutually exclusive active Low outputs.
PHILIPS 74F153 handbook
The 74F153 is a dual 4-input multiplexer that can select 2 bits of data from up to four sources selected by common Select inputs (S0, S1). The two 4-input multiplexer circuits have individual active-Low Enables (Ea, Eb) which can be used to strobe the outputs independently. Outputs (Ya, Yb) are forced Low when the corresponding Enables (Ea, Eb) are High. The 74F153 is the logic implementation of a 2-pole, 4-position switch where the switch is determined by the logic levels supplied to the common select inputs.
PHILIPS 74F151A handbook
The 74F151A is an 8-input multiplexer with high speed, on-chip decoding, multifunctional capability, and complementary outputs. It can provide the ability to select from eight sources of data or control information in one package. The device can provide any logic function of four variables and the negation with correct manipulation.
PHILIPS 74F148 handbook
The 74F148 8-input priority encoder is a Philips Semiconductors product with features such as code conversion, multi-channel D/A converter, decimal-to-BCD converter, cascading for priority encoding of “N” bits, input enable capability, priority encoding-automatic selection of highest priority input line, output enable-active Low when all inputs are High, group signal output-active when any input is Low.
PHILIPS 74F139 handbook
This document describes the product specifications of the 74F139 Dual 1-of-4 decoder/demultiplexer. The device has two independent decoders, each accepting two binary weighted inputs and providing four mutually exclusive active-Low outputs. Each decoder has an active-Low Enable pin, which, when high, forces all outputs to be high. The device has multifunction capability.
PHILIPS 74F132 handbook
This document describes the features and characteristics of the 74F132 Quad 2-input NAND Schmitt trigger. It is capable of transforming slowly changing input signals into sharply defined, jitter-free output signals, and has greater noise margin than conventional NAND gates.