Philips manuals, page 36
PHILIPS BT132 series D handbook
The document describes the features and characteristics of Philips Semiconductors BT132 series D logic level triacs, including glass passivation, sensitive gate, bidirectional switching, and applications for microcontrollers, logic integrated circuits, and low-power gate trigger circuits.
PHILIPS LM75A handbook
LM75A is a temperature-to-digital converter using an on-chip band-gap temperature sensor and Sigma-delta A-to-D conversion technique. The device is also a thermal detector providing an over-temp detection output. The LM75A contains a number of data registers: Configuration register (Conf) to store the device settings such as device operation mode, OS operation mode, OS polarity and OS fault queue as described in the functional description section; temperature register (Temp) to store the digital temp reading, and set-point registers (Tos & Thyst) to store programmable overtemp shutdown and hysteresis limits, that can be communicated by a controller via the 2-wire serial I2C-bus interface. The device also includes an open-drain output (OS) which becomes active when the temperature exceeds the programmed limits. There are three selectable logic address pins so that eight devices can be connected on the same bus without address conflict. The LM75A can be configured for different operation conditions. It can be set in normal mode to periodically monitor the ambient temperature, or in shutdown mode to minimize power consumption. The OS output operates in either of two selectable m
Philips Semiconductors BT131W series handbook
The BT131W series is a logic level triac produced by Philips Semiconductors. It has a high sensitive gate and is suitable for surface mounting. It can be used for general bidirectional switching and phase control applications. These devices are intended to be interfaced directly to microcontrollers, logic integrated circuits and other low power gate trigger circuits.
Philips Semiconductors BT131W series Manual
This document describes the features and characteristics of Philips Semiconductors BT131W series logic level triacs, which are suitable for surface mounting and intended for use in general purpose bidirectional switching and phase control applications. These devices can be directly interfaced to microcontrollers, logic integrated circuits, and other low power gate trigger circuits.
Philips Semiconductors BT131 series handbook
BT131 series logic level triacs are passivated, sensitive gate triacs in a plastic envelope, intended for use in general purpose bidirectional switching and phase control applications. These devices are intended to be interfaced directly to microcontrollers, logic integrated circuits and other low power trigger circuits.
PHILIPS BT1308-400D/600D handbook
The BT1308-400D/600D logic level triac is intended to be interfaced directly to microcontrollers, logic integrated circuits and other low power gate trigger circuits.
PHILIPS BT1306-400D/600D handbook
BT1306-400D/600D Logic level triac is a logic level sensitive gate triac intended to be interfaced directly to microcontrollers, logic integrated circuits and other low power gate trigger circuits.
PHILIPS NE/SE5539 handbook
PHILIPS NE/SA/SE5532/5532A Internally-compensated dual low noise operational amplifier handbook(1)
The document describes the features and characteristics of the NE/SA/SE5532/5532A dual-channel low noise operational amplifier, which is suitable for applications in high-quality and professional audio equipment, instrumentation and control circuits, and telephone channel amplifiers.
PHILIPS NE/SA/SE5532/5532A Internally-compensated dual low noise operational amplifier handbook
The 5532 is a dual high-performance low noise operational amplifier from Philips Semiconductors. Compared to most of the standard operational amplifiers, such as the 1458, it shows better noise performance, improved output drive capability and considerably higher small-signal and power bandwidths. This makes the device especially suitable for application in high-quality and professional audio equipment, instrumentation and control circuits, and telephone channel amplifiers.
PHILIPS NE/SA/SE5532/5532A handbook
Philips Semiconductors LVDT signal conditioner NE/SA/SE5521 handbook
The NE/SA/SE5521 is a signal conditioning circuit for use with Linear Variable Differential Transformers (LVDTs) and Rotary Variable Differential Transformers (RVDTs). The chip includes a low distortion, amplitude-stable sine wave oscillator with programmable frequency to drive the primary of the LVDT/RVDT, a synchronous demodulator to convert the LVDT/RVDT output amplitude and phase to position information, and an output amplifier to provide amplification and filtering of the demodulated signal.
PHILIPS NE5517/NE5517A/AU5517 Dual operational transconductance amplifier handbook
The AU5517/NE5517 is a dual operational transconductance amplifier with a differential input and push-pull output.
PHILIPS Quad high-performance operational amplifier NE/SE5514 handbook(1)
NE/SE5514 is a high-performance quad operational amplifier with low input bias current and low offset voltage.
PHILIPS Quad high-performance operational amplifier NE/SE5514 handbook
The NE/SE5514 family of quad operational amplifiers sets new standards in bipolar quad amplifier performance. The amplifiers feature low input bias current and low offset voltages. Pinout is identical to LM324/LM348 which facilitates direct product substitution for improved system performance in dual supply applications. Output characteristics are similar to a µA741 with improved slew and drive capability.