Industrial

SPP11N60S5, SPB11N60S5 SPI11N60S5 Cool MOS™ Power Transistor features 600 V VDS, RDS(on) of 0.38 Ω, and ID of 11 A. Its features include: a new revolutionary high voltage technology, ultra low gate charge, periodic avalanche rating, extreme dv/dt rating, ultra low effective capacitances, and improved transconductance.

The SP7651 is a wide input voltage range 3A, 900kHz buck regulator. It has a step-down capability from 2.5V to 20V, with an output voltage down to 0.8V. It has a 3A output capability (up to 5A with air flow) and built-in low RDSON power FETs (typical value of 40 mΩ). The design is highly integrated with minimal components. The regulator operates at a fixed frequency of 900 kHz. It features UVLO detection for both VCC and VIN, over temperature protection, and short circuit protection with auto-restart. The wide bandwidth amplifier allows for type II or III compensation. It has a programmable soft start and fast transient response. High efficiency of greater than 92% is possible. The regulator can perform asynchronous start-up into a pre-charged output. It is available in a small 7mm x 4mm DFN package.

SONIX SN8P1702A/SN8P1703A 8-bit micro-controller build-in 12-bit ADC

The SN75LVDS88B is a TFT LCD panel timing controller with an LVDS interface, suitable for notebook applications, supports XGA resolution, and supports mainstream data and gate drivers.

The SN65C3243 and SN75C3243 consist of three line drivers, five line receivers, and a dual charge-pump circuit with ±15-kV ESD protection pin-to-pin (serial-port connection pins, including GND). These devices provide the electrical interface between an asynchronous communication controller and the serial-port connector. The charge pump and four small external capacitors allow operation from a single 3-V to 5.5-V supply. In addition, these devices include an always-active noninverting output (ROUT2B), which allows applications using the ring indicator to transmit data while the devices are powered down. The devices operate at data signaling rates up to 1 Mbit/s and an increased slew-rate range of 24 V/µs to 150 V/µs.

This document provides information about the SN74LS597DE4 supplier and packaging. It includes details about the different package types, pin counts, and package quantities of the SN74LS597DE4.

SN54HC02 and SN74HC02 are four independent 2-input positive NOR gates that can operate over the full military temperature range of –55°C to 125°C. The SN54HC02 is characterized for operation from –40°C to 85°C.

SN54F244, SN74F244 is an octal buffer/driver with 3-state outputs produced by Texas Instruments. It can drive bus lines or buffer memory address registers. The device is available in plastic small-outline (SOIC) and shrink small-outline (SSOP) packages, ceramic chip carriers, and plastic and ceramic DIPs.

This datasheet provides the pin definition, package types, power supply, and operating temperature range of SN5400, SN7400, SN54LS00, SN74LS00, SN54S00, and SN74S00.

This document introduces the SMP100LC series low capacitance transient surge arrestors. The series has bidirectional protection, voltage range from 8V to 400V, low capacitance from 20pF to 45pF, leakage current IR = 2µA max, holding current IH = 150 mA min, and repetitive peak pulse current IPP = 100 A (10/1000µs). These products are widely used in sensitive equipment requiring protection against lightning strikes and power crossing, such as communication equipment, data communication equipment and audio and video equipment.

SMAB34 is a Schottky diode with low power loss and high efficiency. It is suitable for low voltage, high frequency inverters, freewheeling and polarity protection applications.

This datasheet provides information about SMA5103, including maximum operating voltage, maximum operating current, switching loss, and operating temperature range.

TI and its subsidiaries reserve the right to make changes to their products or to discontinue any product or service without notice. Customers are advised to obtain the latest version of relevant information to verify the current and complete information before placing orders. TI warrants the performance of its semiconductor products according to the specifications applicable at the time of sale and utilizes testing and quality control techniques to support this warranty.

This document describes the features and characteristics of the SLF series inductors, including low profile, low DC resistance, and high current handling capacities. These inductors are suitable for portable telephones, personal computers, hard disk drives, and other electronic equipment. The document provides specifications and recommended reflow soldering conditions for the product.

This document describes the features and characteristics of the SK52-B to SK510-B model products. These products are housed in a plastic package and have a UL 94V-O flammability rating. They are suitable for surface mounted applications and exceed the environmental standards of MIL-S-19500 / 228. The products have low leakage current. The mechanical data includes information about the case material, solder plating on the terminals, polarity, mounting position, and weight.