Industrial

The 74F166 is a high speed 8-bit shift register that has fully synchronous serial parallel data entry selected by an active low parallel enable (PE) input. It also supports synchronous serial data input for easy expansion, clock enable for ”do nothing” mode, asynchronous master reset, and is expandable to 16 bits in 8-bit increments. The 74F166 has an industrial temperature range available (-40°C to +85°C).

The 74F164 is an 8-bit edge-triggered shift register with serial data entry and an output from each of the eight stages

The 74F161A, 74F163A 4-bit binary counters are produced by Philips Semiconductors. They feature synchronous counting and loading, two count enable inputs, positive edge-triggered clock, asynchronous master reset (74F161A) and synchronous reset (74F163A), high speed synchronous expansion, typical count rate of 130MHz and industrial range (-40°C to +85°C).

This document introduces the features and parameters of the 74F157A / 74F158A data selectors / multiplexers. It is a high speed quad 2-input multiplexer which selects 4 bits of data from one of two sources under the control of a common select input (S). When E is high, all of the outputs (Yn) are forced low regardless of all other input conditions. Moving data from two registers to a common output bus is a common use of the 74F157A. The state of the select input determines the particular register from which the data comes. The device is the logic implementation of a 4-pole, 2-position switch where the position of the switch is determined by the logic levels supplied to the select input. The 74F158A is similar, but has inverting outputs (Yn).

The 74F133 is a 13-input NAND gate with a typical propagation delay of 4.0ns and a typical supply current of 2.0mA.

The 74F138 is a 1-of-8 decoder/demultiplexer produced by Philips Semiconductors. It has demultiplexing capability, multiple input enable function, and is ideal for memory chip select decoding.

The 74F14 is a six-inverter Schmitt trigger IC produced by Philips. It accepts standard TTL input signals and provides standard TTL output levels. It can transform slowly changing input signals into sharply defined, jitter-free output signals. In addition, it has greater noise margin than conventional inverters. Each circuit contains a Schmitt trigger followed by a Darlington level shifter and a phase splitter driving a TTL totem-pole output. The Schmitt trigger uses positive feedback to effectively speed-up slow input transitions, and provide different input threshold voltages for positive-going and negative-going input threshold (typically 800mV) is determined internally by resistor ratios and is insensitive to temperature and supply voltage variations.

The 74F113 is a dual negative edge-triggered JK-type flip-flop manufactured by Philips Semiconductors. It features individual J, K, clock (CP), set (SD) inputs, true and complementary outputs. When the asynchronous SD input is low, it forces the outputs to the steady state levels shown in the function table, regardless of the level at the other inputs. When the clock (CP) input is high, the J and K inputs are enabled and data will be accepted. The logic levels at the J and K inputs may be allowed to change while the CP is high, and the flip-flop will perform according to the function table as long as minimum setup and hold times are observed. Output changes are initiated by the high-to-low transition of the CP.

74F112 is a dual J-K negative edge-triggered flip-flop produced by Philips Semiconductors. It has individual J, K, Clock (CPn), Set (SD) and Reset (RD) inputs, true (Qn) and complementary (Qn) outputs. When the SD and RD inputs are low, they set or reset the outputs as shown in the Function Table, regardless of the level at the other inputs. A high level on the clock (CPn) input enables the J and K inputs and data will be accepted. The logic levels at the J and K inputs may be allowed to change while the CPn is high and flip-flop will perform according to the Function Table as long as minimum setup and hold times are observed. Output changes are initiated by the High-to-Low transition of the CPn.

74F109 is a dual positive edge-triggered JK-type flip-flop produced by Philips. It has independent J, K, clock, set, and reset inputs. The device works in the temperature range of -40 ° C to +85 ° C, with a maximum clock frequency of 125MHz and a typical current of 12.3mA.

This document describes the product specifications of the 74F08 quad two-input AND gate integrated circuit from Philips Semiconductors. It includes information on pin configuration, operating temperature range, propagation delay, and supply current.

The 74F04 is a hex inverter chip launched by Philips. Its operating voltage is 5V and its working temperature range is -40 to +85 degrees. The pin definition is 14-pin plastic DIP.

This document is the 74F02 Quad 2-input NOR gate product specification, which introduces the features, characteristics and usage methods of the product.

74F00 is a quad 2-input NAND gate circuit produced by PHILIPS. Its feature is the industrial temperature range (-40°C to +85°C). The rated input high/low voltage is 20µA/0.6mA, and the rated output high/low voltage is 1.0mA/20mA.

BLF900-110 and BLF900S-110 are two RF power amplifiers produced by Philips Semiconductors, suitable for GSM, EDGE and CDMA base stations and multicarrier applications in the 800 to 1000 MHz frequency range.