Industrial

NE522 is Philips Semiconductors' Linear Products high-speed dual-differential comparator/sense amp. It has 15ns maximum guaranteed propagation delay, 20µA maximum input bias current, TTL-compatible strobes and outputs, large common-mode input voltage range and operates from standard supply voltages.

The NE52118 is a low noise amplifier with a typical noise figure of 1.0 dB, a typical gain of 15.0 dB and a typical gain-bandwidth product of 15.0 dB. It is housed in a 4-pin super mini-mold package and has a grounded emitter.

NE521 is a high-speed dual-differential comparator/sense amplifier with features including 12ns maximum guaranteed propagation delay, 20µA maximum input bias current, TTL compatible strobes and outputs, and large common-mode input voltage range. It is suitable for applications such as MOS memory sense amplifier, A-to-D conversion, and high-speed line receiver.

NE5210 is a low-noise, wide-band transimpedance amplifier from Philips Semiconductors, suitable for signal recovery in fiber-optic receivers. It features single 5V supply, 280MHz bandwidth, differential outputs, low input/output impedances, high power supply rejection ratio, high overload threshold current, wide dynamic range, and 7kΩ differential transresistance.

The NE5209 is a wideband variable gain amplifier that combines high-speed bipolar process with the Gilbert architecture. It features single DC voltage control for gain, operates on a single 5V power supply, and consumes only 40mA. The amplifier has high impedance differential inputs and 50Ω differential outputs, allowing for AGC, impedance transformation, and balun functions.

The NE/SA5204A is a wide-band high-frequency amplifier with a fixed gain of 20dB. It is ideal for cable TV applications.

The NE/SA5090 addressable relay driver is a high-current latched driver, similar in function to the 9934 address decoder. The device has 8 open-collector Darlington power outputs, each capable of 150mA load current. The outputs are turned on or off by respectively loading a logic “1” or logic “0” into the device data input. The required output is defined by a 3-bit address. The device must be enabled by a CE input line which also serves the function of further address decoding. A common clear input, CLR, turns all outputs off when a logic “0” is applied. The device is packaged in a 16-pin plastic or Cerdip package.

This document describes the features and characteristics of the NE5080 supplier.

The NE5037 is a low cost, complete successive-approximation analog-to-digital (A/D) converter, fabricated using Bipolar/I2L technology. With an external reference voltage, the NE5037 will accept input voltages between 0V and VREF. An external START pulse of at least 300ns in duration will provide the 6-bit result of the conversion in parallel format. Full conversion with no missing codes occurs in 9µs.

NE5020 is a microprocessor-compatible monolithic 10-bit digital-to-analog converter subsystem. This device offers 10-bit resolution and ±0.1% accuracy and monotonicity guaranteed over full operating temperature range. Low loading latches, adjustable logic thresholds, and addressing capability allow the NE5020 to directly interface with most microprocessor- and logic-controlled systems. The NE5020 contains internal voltage reference, DAC switches and resistor ladder. Also, the input buffer and output summing amplifier are included. In addition, the matched application resistors for scaling either unipolar or bipolar output values are included on a single monolithic chip. The result is a near minimum component count 10-bit resolution DAC system.

The NE/SE5018/19 is a complete 8-bit digital-to-analog converter subsystem with features such as input latches and low-loading data inputs.

The DAC08 series is an 8-bit monolithic multiplying Digital-to-Analog Converter that provides very high-speed performance, low cost, and outstanding applications flexibility. Advanced circuit design achieves 70ns settling times with very low glitch and at low power consumption. Monotonic multiplying performance is attained over a wide 20-to-1 reference current range. Matching to within 1 LSB between reference and full-scale currents eliminates the need for full-scale trimming in most applications. Direct interface to all popular logic families with full noise immunity is provided by the high swing, adjustable threshold logic inputs. Dual complementary outputs are provided, increasing versatility and enabling differential operation to effectively double the peak-to-peak output swing. True high voltage compliance outputs allow direct output voltage conversion and eliminate output op amps in many applications. All DAC08 series models guarantee full 8-bit monotonicity and linearities as tight as 0.1% over the entire operating temperature range. Device performance is essentially unchanged over the ±4.5V to ±18V power supply range, with 37mW power consumption attainable at ±5V supplies. The compact size and low power consumption make the DAC08 attractive for portable and military aerospace applications.