National Manuals

The LM118/LM218/LM318 precision high speed operational amplifiers are designed for applications requiring wide bandwidth and high slew rate. They feature a factor of ten increase in speed over general purpose devices without sacrificing DC performance. The LM118 series has internal unity gain frequency compensation. This considerably simplifies its application since no external components are necessary for operation. However, unlike most internally compensated amplifiers, external fre- quency compensation may be added for optimum perfor- mance. For inverting applications, feedforward compensa- tion will boost the slew rate to over 150V/µs and almost double the bandwidth. Overcompensation can be used with the amplifier for greater stability when maximum bandwidth is not needed. Further, a single capacitor can be added to reduce the 0.1% settling time to under 1 µs. The high speed and fast settling time of these op amps make them useful in A/D converters, oscillators, active filters, sample and hold circuits, or general purpose amplifiers. These devices are easy to apply and offer an order of magnitude better AC performance than industry standards such as the LM709. The LM218 is identical to the LM118 except that the LM218 has its performance specified over a −25˚C to +85˚C tem- perature range. The LM318 is specified from 0˚C to +70˚C.

LM20EP Enhanced Plastic 2.4V, 10µA, SC70, micro SMD Temperature Sensor is a precision analog output CMOS integrated circuit temperature sensor produced by National Instruments Corporation. The working temperature range is -55˚C to +130˚C, and the power supply operating range is +2.4 V to +5.5 V. The output signal of the sensor is linearly related to the temperature, and the linearity of the output signal is ±1.5˚C. The power consumption is less than 10µA, and the self-heating in the static state is less than 0.02˚C.

The LM2005 is a dual high power amplifier designed for automotive applications. It has high current capability (3.5A), delivering 10W/channel into 2X (LM2005T-S) or 20W bridged monaural (LM2005T-M) into 4X, with low distortion, low noise, and high peak current capability.

This document is a copyright statement.

1-to-8 minimum skew clock driver, is National Semiconductor Corporation's CSG series products, used for signal generation and clock distribution, with guaranteed pin-to-pin and part-to-part skew, can be used as military versions

DS90CR286A and DS90CR216A are +3.3V rising edge data strobe LVDS receivers that convert LVDS data streams into parallel CMOS/TTL data. This chipset is an ideal solution for solving EMI and cable size problems associated with wide, high-speed TTL interfaces.

The DS90CR286A and DS90CR216A are +3.3V rising edge data strobe LVDS receivers that convert LVDS data streams into parallel CMOS/TTL data streams. This chipset is an ideal solution for EMI and cable size problems associated with wide, high-speed TTL interfaces.

DS90CR215/DS90CR216 +3.3V Rising Edge Data Strobe LVDS 21-Bit Channel Link - 66 MHz Product Overview

The DS90CR215/DS90CR216 is a +3.3V rising edge data strobe 21-bit channel link that uses LVDS technology for data transmission. The product features high-speed transmission, stable signals, and low cable requirements.

The DS90CR213/DS90CR214 21-Bit Channel Link—66 MHz is a 21-bit channel link chipset from Texas Instruments. The chip supports 66MHz clock and can provide up to 1.386Gbit/s data throughput.

This document is an overview of the DS90CR211/DS90CR212 21-Bit Channel Link product, introducing the features and characteristics of the product.

DS90CP22 is a 2x2 crosspoint switch utilizing LVDS technology for low power, high speed operation. Data paths are fully differential from input to output for low noise generation and low pulse width distortion. The non-blocking design allows connection of any input to any output or outputs. LVDS I/O enable high speed data transmission for point-to-point interconnects. This device can be used as a high speed differential crosspoint, 2:1 mux, 1:2 demux, repeater or 1:2 signal splitter. The mux and demux functions are useful for switching between primary and backup circuits in fault tolerant systems. The 1:2 signal splitter and 2:1 mux functions are useful for distribution of serial bus across several rack-mounted backplanes.

The DS90CP04 is a 4×4 digital crosspoint switch that uses low voltage differential signaling (LVDS) technology to achieve low power consumption and high speed operation. The data path is all composed of differential circuits to suppress noise. Non-blocking architecture allows connection of any input bit to any output bit (single output or multiple outputs). The switch matrix contains 4 sets of differential 4:1 multiplexers. Each multiplexer is connected to all 4 input channels and can output any 1 input channel from any output channel. Each output pair of DS90CP04 can operate independently at up to 2.5Gbit/s. The MODE pin is used to switch between the easy-to-control serial control interface or the configuration selection port. The serial control interface can use a single load command to update the new switch configuration information for all outputs at one time. The direct configuration port can directly change the output configuration based on the logic level decoded information of the SEL0/1 pins.

DS90CF583/DS90CF584 LVDS 24-Bit Color Flat Panel Display (FPD) Link— 65 MHz. This chipset is an ideal means to solve EMI and cable size problems associated with wide, high speed TTL interfaces.

DS90CF581�DS90CF582 LVDS 24-Bit Color Flat Panel Display (FPD) Link is a chipset released by National Semiconductor for connecting displays and motherboards. The chipset uses a 40MHz clock frequency to convert 28 bits of CMOS�TTL data into four LVDS data streams, and transmits the data through the fifth LVDS link to the display. DS90CF581 can transmit 40MHz clock signal and 4 LVDS data streams to the display, and DS90CF582 can convert the received 4 LVDS data streams to 28 bits of CMOS�TTL data stream and output the data to the motherboard. The chipset has low power consumption, low EMI and other features.