Industrial

CD54ACT86 and CD74ACT86 are quadruple 2-input exclusive-OR gates. They perform the Boolean function Y = A⊕B or Y = AB + AB in positive logic. The devices have TTL-voltage compatibility, fast speed, low power consumption, ±24mA output drive current, fanout to 15 F devices, SCR-Latchup-Resistant CMOS process and circuit design, and exceed 2-kV ESD protection per MIL-STD-883, Method 3015.

SN54HC86, SN74HC86 are quadruple 2-input exclusive-OR gates with a wide operating voltage range of 2V to 6V. They can drive up to 10 LSTTL loads, have low power consumption, strong output drive capability, and low input current.

The CD74AC86 is a quadruple 2-input exclusive-OR gate. This device performs the Boolean function Y = A ⊕ B or Y = AB + AB in positive logic. A common application is as a true/complement element. If one of the inputs is low, the other input is reproduced in true form at the output. If one of the inputs is high, the signal on the other input is reproduced inverted at the output.

The MAX7301 is a 4-wire serial interface I/O expander chip from MAXIM Corporation. It supports 20/28 I/O ports and can be configured as open drain output, Schmitt input, Schmitt input with internal pull-up, and supports logic transition detection. The maximum operating current is 11µA, and the operating temperature range is -40℃~+125℃

The MAX7310 is a 2-wire interfaced 8-bit I/O port expander with reset. It provides 8-bit parallel input/output port expansion for SMBus-compatible and I2C-compatible applications. The MAX7310 consists of an input port register, an output port register, a polarity inversion register, a configuration register, a bus timeout register, and an SMBus/I2C-compatible serial interface. The system master can invert the MAX7310 input data by writing to the active-high polarity inversion register. The system master can enable or disable bus timeout by writing to the bus timeout register. Any of the eight I/O ports may be configured as input or output. An active-low reset input sets the eight I/Os as inputs. Three address select pins configure one of 56 slave ID addresses. The MAX7310 is available in 16-pin thin QFN, TSSOP, and QSOP packages and is specified over the -40°C to +125°C automotive temperature range.

MAX7321 is an 8-channel I/O open-drain output chip launched by Texas Instruments (TI). It can be used to receive and drive sensor analog signals. The maximum working voltage is 5.5V and the working temperature range is -40°C to +125°C.

The MAX7316 is an I2C/SMBus-compatible serial interfaced peripheral that provides microprocessors with eight additional I/O ports plus one output-only port and one input-only port. Each I/O port can be individually configured as an open-drain current-sinking output rated to 50mA at 5.5V or as a logic input with transition detection. The output-only port can also be assigned as an interrupt output for transition detection. The outputs are capable of driving LEDs or providing logic outputs with external resistive pullup up to 5.5V. Eight-bit PWM current control is available for all nine output ports. Four bits are global control and apply to all LED outputs to provide coarse adjustment of current from fully off to fully on in 14 intensity steps. Additionally, each output has individual 4-bit control, which further divides the globally set current into 16 more steps. Alternatively, the current control can be configured as a single 8-bit control that sets all outputs at once. Each output has independent blink timing with two blink phases. LEDs can be individually set to be on or off during either blink phase or to ignore the blink control. The blink period is controlled by an external clock input (up to 1kHz) on BLINK or by a register. The BLINK input can also be used as a logic control to turn the LEDs on and off or as a general-purpose input. The MAX7316 supports hot insertion. All port pins, the INT output, SDA, SCL, RST, BLINK, and the slave a

The MAX7315 is an I2C-/SMBus-compatible serial interfaced peripheral that provides microprocessors with 8 I/O ports. Each I/O port can be individually configured as either an open-drain current-sinking output rated at 50mA at 5.5V, or a logic input with transition detection. A ninth port can be used for transition detection interrupt or as a general-purpose output. The outputs are capable of directly driving LEDs, or providing logic outputs with external resistive pullup up to 5.5V. PWM current drive is integrated with 8 bits of control. Four bits are global control and apply to all LED outputs to provide coarse adjustment of current from fully off to fully on in 14 intensity steps. Each output then has individual 4-bit control, which further divides the globally set current into 16 more steps. Alternatively, the current control can be configured as a single 8-bit control that sets all outputs at once. The MAX7315 is pin and software compatible with the PCA9534 and PCA9554(A). Each output has independent blink timing with two blink phases. All LEDs can be individually set to be on or off during either blink phase, or to ignore the blink control. The blink period is controlled by a register. The MAX7315 supports hot insertion. All port pins, the INT output, SDA, SCL, and the slave address inputs ADO-2 remain high impedance in power-down (V+ = 0V) with up to 6V asserted upon them.

The CD54HC86 and CD74HC86 contain four independent EXCLUSIVE OR gates with low power consumption and broad applications.

The MAX7314 is a 16-bit I/O expander from TI that supports I2C bus interface. This device can be configured as output ports or input ports, output ports can drive LEDs, and input ports can detect logic levels. The MAX7314 has a built-in 8-bit PWM current control that can be used to control the current of all 17 output ports.

This document is about 'HC7266 data sheet, which introduces the features of the product, including four independent EXCLUSIVE NOR gates, buffered inputs and outputs, logical comparators, parity generators and checkers, adders/subtracters, standard outputs and bus driver outputs, operating temperature range, propagation delay and transition times, power consumption, HC types, working voltage and noise immunity.

The MAX7313 is a 16 I/O port I2C-compatible serial interface peripheral that can be configured as either an open-drain current-sinking output or a logic input with transition detection. It supports PWM current drive and is pin and software compatible with the MAX7311, PCA9535, and PCA9555.

The SN74LVC86A is a quad 2-input exclusive-OR gate manufactured by TI. The device operates in the 2.7-V to 3.6-V VCC voltage range and implements the Boolean function Y=A⊕B or Y=AB+AB in positive logic. A common application is as a true/complement element. If one of the inputs is low, the output is high.

CD4030B is an integrated circuit chip produced by Texas Instruments Incorporated.

The DS4520 is a 9-bit nonvolatile (NV) I/O expander with 64 bytes of NV user memory controlled by an I2C- compatible serial interface. The DS4520 offers users a digitally programmable alternative to hardware jumpers and mechanical switches that are being used to control digital logic nodes. Furthermore, the digital state of each pin can be read through the serial interface. Each I/O pin is independently configurable. The outputs are open drain with selectable pullups. Each output has the ability to sink up to 12mA. Since the device is NV, it powers up in the desired state allowing it to control digital logic inputs immediately on power-up without having to wait for the host CPU to initiate control.