Industrial

The AD7651 is a 16-bit, 100 kSPS, PulSAR unipolar ADC with reference, operating from a single 5V supply.

This document introduces the features and characteristics of the Huawei nova 9 series phones, including the phones' appearance design, performance configuration, and camera function.

This is a MMIB2B multi media interface board specification sheet, which introduces the features and characteristics of the product.

ds1982 1024-bit eprom datasheet

LT1573 is a low cost, high current, low dropout, fast transient response regulator driver IC that can be used with an external PNP power transistor to provide up to 5A of current with a dropout voltage as low as 0.35V. The device is designed for extremely fast transient response. This greatly reduces bulk storage capacitance when the regulator is used in applications with fast, high current load transients. To keep cost and complexity low, the LT1573 uses a new time-delayed latching overcurrent protection technique that requires no external current sense resistor. Base drive is limited for instantaneous protection, and a time-delayed latch protects the regulator from continuous short circuits. The LT1573 is available in both adjustable and fixed versions with a operating voltage range of 2.8V to 10V.

This document describes the features and characteristics of STMicroelectronics' P80NF55-06 series power MOSFET products, including low on-resistance, exceptional dv/dt capability, 100% avalanche tested, and application-oriented characterization. The product is suitable for high-efficiency DC-DC converters, UPS and motor control, automotive environment, and other applications.

BWR Series 3 Watt, Dual Output DC/DC Converters are fully regulated (±0.5% max. line, ±1% max. load), fully isolated (1000Vdc minimum), extremely efficient (as high as 78% guaranteed) building blocks providing true component-like flexibility and convenience to designers of modern distributed power systems.

This document introduces the technical parameters, application scenarios, features and advantages of AMP connectors, such as the suitability for 28-16 AWG [0.08-1.2 mm2] cables, no need for wire stripping, compact and lightweight, easy to operate, suitable for prototypes or low- to medium-volume production, etc.

This datasheet introduces the features of the Micrel MIC4723 3A 2MHz integrated switch buck regulator

LM109/LM309 5-Volt Regulator

MAX17005/MAX17006/MAX17015 are high-frequency multichemistry battery chargers. These circuits feature a new high-frequency current-mode architecture that significantly reduces component size and cost*. The charger uses a high-side MOSFET with n-channel synchronous rectifier. Widely adjustable charge current, charge voltage, and input current limit simplify the construction of highly accurate and efficient chargers. The charge voltage and charge current are set with analog control inputs. The charge current setting can also be adjusted with a PWM input. High-accuracy current-sense amplifiers provide fast cycle-by-cycle current-mode control to protect against short circuits to the battery and respond quickly to system load transients. In addition, the charger provides a high-accuracy analog output that is proportional to the adapter current. In the MAX17015, this current monitor remains active when the adapter is absent to monitor battery discharge current. The MAX17005 charges three or four Li+ series cells, and the MAX17006 charges two or three Li+ series cells. The MAX17015 adjusts the charge voltage setting and the number of cells through a feedback resistor-divider from the output. All variants of the charger can provide at least 4A of charge current with a 10mΩ sense resistor. The charger utilizes a charge pump to control an n-channel adapter selection switch. The charge pump remains active even when the charger is off. When the adapter is connected to the charger, the charger will charge the battery through the charge pump. When the charge is finished, the charge pump is turned off and the adapter will continue to power the battery.

This document describes the features of the K817P/ K827PH/ K847PH optocouplers, including endstackable design, DC isolation test voltage, low coupling capacitance, current transfer ratio selection, low temperature coefficient, wide ambient temperature range, etc.

VLMW82.. is a LED light source produced by Vishay Semiconductors. It uses InGaN technology and has low thermal resistance and high optical power. The light efficiency can reach 40 lm/W at 100 mA. The product complies with RoHS 2002/95/EC and WEEE 2002/96/EC standards and has been certified by AEC-Q101.

VLMS31.. is a high intensity SMD LED produced by Vishay Semiconductors. It has excellent brightness and low power consumption. It can be used in automotive, communication, audio and video equipment, office equipment and other fields.