Industrial

STE180NE10 is an N-channel 100V - 4.5 mΩ - 180A ISOTOP STripFET POWER MOSFET product of STMicroelectronics, with a typical RDS(on) of 4.5 mΩ, 100% avalanche testing, low intrinsic capacitance, minimized gate charge and reduced voltage spread.

STE180N10 is a N-channel power MOSFET from ISOTOP company. Its features are RDS(on) typical value is 5.5mΩ, 100% avalanche tested, low parasitic capacitance, minimized gate charge and reduced voltage spread.

STE15NA100 N is an N-channel enhancement mode fast power MOS transistor with low RDS(on), high current, large SOA, easy to mount, etc. It is suitable for applications such as SMPS and UPS, motor control, welding equipment, PWM output stage, ultrasonic circuits, etc.

STE110NS20FD is a N-channel 200V - 0.022Ω - 110A ISOTOP MESH OVERLAY™ Power MOSFET device produced by STMicroelectronics. The device has the following features: typical RDS(on) = 0.022Ω, extremely high dv/dt capability, 100% avalanche tested, minimized gate charge, ±20V gate to source voltage rating, low intrinsic capacitance and fast body-drain diode: low trr, Qrr. The device is suitable for high current, high speed switching, switch mode power supply (SMPS), welding equipment DC-AC converter and uninterrupted power supply and motor drive applications.

STE110NA20 is an N-channel enhancement mode fast power MOS transistor with features such as low on-resistance, high current power module, large SOA, easy mounting, low thermal resistance, and low internal parasitic inductance. It is suitable for applications such as SMPS, UPS, motor control, welding equipment, output stage for PWM, ultrasonic circuits, etc.

The STE100P, also referred to as STEPHY1, is a high performance Fast Ethernet physical layer interface for 10BASE-T and 100BASE-TX applications. It was designed with advanced CMOS technology to provide a Media Independent Interface (MII) for easy attachment to 10/100 Media Access Controllers (MAC) and a physical media interface for 100BASE-TX of IEEE802.3u and 10BASE-T of IEEE802.3. The STEPHY1 supports both half-duplex and full-duplex operation, at 10 and 100 Mbps operation. Its operating mode can be set using auto-negotiation, parallel detection or manual control. It also allows for the support of auto-negotiation functions for speed and duplex detection.

This document is about STE10/100A datasheet

The STE10/100 is a high performance PCI Fast Ethernet controller with integrated physical layer interface for 10BASE-T and 100BASE-TX applications. It was designed with advanced CMOS technology to provide a glueless 32-bit bus master interface for the PCI bus, boot ROM interface, CSMA/CD protocol for Fast Ethernet, as well as the physical media interface for 100BASE-TX of IEEE802.3u and 10BASE-T of IEEE802.3. The auto-negotiation function is also supported for speed and duplex detection. The STE10/100 provides both half-duplex and full-duplex operation, as well as support for full-duplex flow control. It provides long FIFO buffers for transmission and receiving, and early interrupt mechanism to enhance performance. The STE10/100 also supports ACPI and PCI compliant power management function.

This document introduces STE10/100, a high performance PCI Fast Ethernet controller with integrated physical layer interface for 10BASE-T and 100BASE-TX application.

This product is a PCI Fast Ethernet controller that supports 10BASE-T and 100BASE-TX applications.

BTA16 B BTB16 B triacs are high performance glass passivated PNPN devices. These parts are suitables for general purpose ap- plications where high surge current capability is re- quired. Application such as phase control and static switching on inductive or resistive load.

BTA16 BW/CW BTB16 BW/CW is a high performance triac family from Schneider Electric. The product has high switching speed, high surge current, high rated voltage and other characteristics. It is widely used in phase control and static switching applications.

BTA16 B BTB16 B are high performance glass passivated PNPN devices, suitable for general purpose applications where high surge current capability is required. For example, phase control and static switching on inductive or resistive load.