Industrial

The FT245BL is the lead free version of the 2nd generation of FTDI’s popular USB FIFO I.C. This device not only adds extra functionality to its FT8U245AM predecessor and reduces external component count, but also maintains a high degree of pin compatibility with the original, making it easy to upgrade or cost reduce existing designs as well as increasing the potential for using the device in new application areas.

The LTC3717 is a synchronous step-down switching regulator controller from Texas Instruments for DDR and QDR memory termination. The controller uses a valley current control architecture to deliver very low duty cycles without requiring a sense resistor. Operating frequency is selected by an external resistor and is compensated for variations in VIN. Forced continuous operation reduces noise and RF interference. Output voltage is internally set to half of VREF, which is user programmable. Fault protection is provided by an output overvoltage comparator and optional short-circuit shutdown timer. Soft-start capability for supply sequencing is accomplished by internally compensating VIN's variation with switching frequency.

This document introduces CD4 Power's UHE series isolated high-efficiency DC/DC converters, which have high output power, low power consumption, small size, multiple output configurations, high efficiency, stable no-load operation and other features

EL4332 is a high-performance triple 2:1 video switch amplifier from Intersil. It supports TTL/CMOS compatible A/B control, 3ns switching time and 300MHz bandwidth, which can meet the performance requirements of the fastest component video systems. EL4332 uses a narrow 16-pin small outline package and operates at a standard ±5V supply voltage.

This document describes the features and characteristics of Vishay Semiconductors VLME31 series high-intensity SMD LED, including brightness, package standard, compatibility, etc. This product is suitable for automotive, communication, audio and video equipment, office equipment, etc.

The DS12885, DS12887, and DS12C887 real-time clocks (RTCs) are designed to be direct replacements for the DS1285 and DS1287. The devices provide a real-time clock/calendar, one time-of-day alarm, three maskable interrupts with a common interrupt output, a programmable square wave, and 114 bytes of battery-backed static RAM (113 bytes in the DS12C887 and DS12C887A). The DS12887 integrates a quartz crystal and lithium energy source into a 24-pin encapsulated DIP package. The DS12C887 adds a century byte at address 32h. For all devices, the date at the end of the month is automatically adjusted for months with fewer than 31 days, including correction for leap years. The devices also operate in either 24-hour or 12-hour format with an AM/PM indicator. A precision temperature-compensated circuit monitors the status of VCC. If a primary power failure is detected, the device automatically switches to a backup supply. A lithium coin-cell battery can be connected to the VBAT input pin on the DS12885 to maintain time and date operation when primary power is absent. The device is accessed through a multiplexed byte-wide interface, which supports both Intel and Motorola modes.

MAX132 is a 18-bit CMOS serial output ADC with low supply current, high resolution and low noise. It is suitable for applications such as data loggers, weigh scales, data acquisition systems and panel meters.

This document introduces NCP101X series products. The series integrates a fixed frequency current mode controller and a 700 V MOSFET. It is housed in a PDIP-7, PDIP-7 Gull Wing, or SOT-223 package. It provides soft start, frequency jittering, short circuit protection, skip cycle, a maximum peak current setpoint and a Dynamic Self-Supply (no need for an auxiliary winding). The switching frequency is 65-100-130 kHz. When the current setpoint falls below a given value, e.g. the output power demand diminishes, the IC automatically enters the so-called skip-cycle mode and provides excellent efficiency at light loads. No acoustic noise takes place. Short-circuit detection takes place when the feedback signal fades away, e.g. in true short-circuit conditions or in broken Optocoupler cases. External disabling can be easily done either simply by pulling the feedback pin down or latching it to ground through an inexpensive SCR for complete latched-off.

This document is a product guide for Toshiba semiconductor products. The guide includes a list of products categorized by function and application, package diagrams, taping information, a list of lead-formed products, and an overall list of devices. Toshiba power transistors achieve high levels of current efficiency through the use of minute patterns and high-density MET design.

LTC2926 is a MOSFET-controlled power supply tracker that allows tracking and sequencing of up to three power supply rails. It features adjustable ramp rates, offsets, and time delays, and automatic remote sense switching to compensate for voltage drops across the MOSFETs. The product is suitable for VCORE and VI/O supply tracking, microprocessor, DSP and FPGA supplies, servers, communication systems, etc.

TB6612FNG is a dual DC motor driver IC from Toshiba. It features an output current of 1.2 A, a maximum operating voltage of 15V, and low ON resistance. The chip also has over temperature protection and under voltage detection.

The LT ®1765 is a monolithic buck switching regulator from Texas Instruments. It integrates a high efficiency 3A, 0.09Ω switch and all the control circuitry required to construct a high frequency, current mode switching regulator. The chip can operate at a wide input voltage range of 3V to 25V and output a maximum current of 3A.

TEMT3700 is a high sensitivity, high speed silicon NPN phototransistor produced by Vishay.

This is a guide specification of TOSHIBA G9000 80/100/160/225 kVA three-phase static uninterruptible power supply