Industrial

TME series is a range of sub-miniature , isolated DC/DC-con- verters in a SIP-package, which requires only 0.7 cm2 of board space. They provide a cost effective solution to generate supplemen- tary, isolated voltages.

TM2SN64EPH and TM4SN64EPH are two synchronous dynamic random access memory (SDRAM) modules that can be used in 66MHz 4-Clock systems. They use a single 3.3V power supply and support read latencies 2 and 3. Both modules support byte read/write capability and have a high performance range, high speed, low noise, low voltage TTL (LVTTL) interface, support burst interleave and burst interrupt operations, burst length programmable to 1, 2, 4 and 8, have two banks for on-chip interleaving (gapless access), an ambient temperature range of 0°C to 70°C, gold-plated contacts, a pipeline architecture and use EEPROM for serial presence detection (SPD).

MLL1.4KESD5.0-1.4KESD170A is a surface mount transient voltage suppressor produced by Microsemi. It can effectively protect sensitive components from ESD and EFT transient voltages in circuit design.

1102A-1110UFA is a single phase bridge voltage multiplier produced by Voltage Multipliers Inc. The rated working voltage is 200V-1000V, the rated working current is 1.4A-1.5A, and the rated recovery time is 70ns-3000ns.

The TLV245x is a family of rail-to-rail input/output operational amplifiers that sets a new performance point for supply current and ac performance. These devices consume a mere 23 µA/channel while offering 220 kHz of gain-bandwidth product, much higher than competitive devices with similar supply current levels. Along with increased ac performance, the amplifier provides high output drive capability, solving a major shortcoming of older micropower rail-to-rail input/output operational amplifiers. The TLV245x can swing to within 250 mV of each supply rail while driving a 2.5-mA load. Both the inputs and outputs swing rail-to-rail for increased dynamic range in low-voltage applications. This performance makes the TLV245x family ideal for portable medical equipment, patient monitoring systems, and data acquisition.

This document introduces the features and characteristics of the 256Kbit and 128Kbit serial I2C bus EEPROM M24128-BW, M24128-BR, M24256-BW, M24256-BR

This document is the datasheet of the TLV.4200 series backlit LED. The series LED has high light output, wide viewing angle, classified luminous flux, tinted transparent package, low power dissipation, low self-heating, rugged design and high reliability. It can be used for backlighting display panel, LCD display, switch symbol, keyboard, graphic board and measuring scale etc.

10 amp plug-in power relay, available in I2PCO and 3PCO, with a large selection of models with different operating options. Arc barriers prevent flashover between contacts, and a manual operator for circuit testing is available in a color-coded version for AC/DC identification. A mechanical flag indicator shows armature operation, and gold flashed contacts are standard.

The 100331 is a low power triple D flip-flop with true and complement outputs, a Common Clock (CPC) and Master Set (MS) and Master Reset (MR) inputs. Each flip-flop has individual Clock (CPn), Direct Set (SDn) and Direct Clear (CDn) inputs. Data enters a master when both CPn and CPC are LOW and transfers to a slave when CPn or CPC (or both) go HIGH. The Master Set, Master Reset and individual CDn and SDn inputs override the Clock inputs. All inputs have 50 kΩ pull-down resistors.

The 100314 is a monolithic quint differential line receiver with emitter-follower outputs. An internal reference supply (VBB) is available for single-ended reception. When used in single-ended operation the apparent input threshold of the true inputs is 25 mV to 30 mV higher (positive) than the threshold of the complementary inputs. Unlike other F100K ECL devices, the inputs do not have input pull-down resistors. Active current sources provide common-mode rejection of 1.0V in either the positive or negative direction. A defined output state exists if both inverting and non-inverting inputs are at the same potential between VEE and VCC. The defined state is logic HIGH on the Oa-Oe outputs.

The TLE207x series of JFET-input operational amplifiers more than double the bandwidth and triple the slew rate of the TL07x and TL08x families of BiFET operational amplifiers. Texas Instruments Excalibur process yields a typical noise floor of 11.6 nV/√Hz, 17-nV/√Hz ensured maximum, offering immediate improvement in noise-sensitive circuits designed using the TL07x. The TLE207x also has wider supply voltage rails, increasing the dynamic signal range for BiFET circuits to ±19 V. On-chip zener trimming of offset voltage yields precision grades for greater accuracy in dc-coupled applications. The TLE207x are pin-compatible with lower performance BiFET operational amplifiers for ease in improving performance in existing designs. BiFET operational amplifiers offer the inherently higher input impedance of the JFET-input transistors, without sacrificing the output drive associated with bipolar amplifiers. This makes them better suited for interfacing with high-impedance sensors or very low-power loads.

RPM5300 series are remote control receiver modules. They are small-sized, light-weight, and low current consumption modules. They have Top view package and Side view package two kinds of packaging.

LTV8141 is a switch regulator available in 4-pin, 8-pin, and 16-pin DIP packages. It is UL, TUV, CSA, and FIMKO approved.