Industrial

The product is a 30-watt E series DC/DC converter from recom, supporting 1.6 kV isolation and wide input range (single output). The features are 24V and 48V input range, optional output voltages of 1.8V, 2.5V, 3.3V, 5V, 12V and 15V, and maximum capacitive loads of 6500μF, 19500μF, 10200μF, 10200μF, 3300μF and 1100μF.

This document describes the features and applications of the DCR760N series double side cooled phase control thyristors from Dynex Semi. The product features double side cooling and high surge capability, and is suitable for medium voltage soft starts, high voltage power supplies, and static switches.

This document describes the features and characteristics of the DCR1277SD model, including high power drives, high voltage power supplies, and DC motor control. The product features double side cooling, high surge capability, high mean current, and fatigue-free operation.

The LTC1749 is an 80Msps, 12-bit A/D converter designed for digitizing wide dynamic range signals up to frequencies of 500MHz. The input range of the ADC can be optimized with the on-chip PGA sample-and-hold circuit and flexible reference circuitry.

ZD2.4 THRU ZD36 ZENER DIODES are Zenar Diodes produced by Unisonic Technologies Co., Ltd., which have features of high-density mounting, high demand voltage range and high-efficient non-wire bonding.

YB1231 is a series of ultra-low-noise, low dropout (LDO) linear regulators with 2.0% output voltage accuracy

This is an introduction to the Xilinx XC5200 FPGA product. It introduces the main features, performance, functions, application scenarios of this product.

The XC2173 series are high frequency, low power consumption CMOS ICs with built-in crystal oscillator, divider and clock multiplier PLL circuits. Output is selectable from any one of the following values for f0 : f0 x 5, f0 x 6, f0 x 7, f0 x 8, f0/2, f0/4, f0/8. With an oscillation capacitor & oscillation feedback resistor built-in, a stable oscillator circuit can be put together using only an external crystal oscillator. By connecting an external standard clock, the above mentioned output frequencies can be achieved.

The X9408 is a low noise, low power, 2-wire bus quad digitally controlled potentiometer with 40 ohm typical resistance, four non-volatile data registers, 2.7V to 5.5V operation, 10k ohm, 2.5k ohm end to end resistances, 100,000 data changes per bit per register, 100 years data retention, and three packages: 24 pin SOIC, TSSOP, and PDIP.

This document is the PDF datasheet for Intersil X9317, which introduces the features and characteristics of the product.

The X25080 is a CMOS 8192-bit serial E2PROM, internally organized as 1K x 8. The X25080 features a Serial Peripheral Interface (SPI) and software protocol allowing operation on a simple three-wire bus. The bus signals are a clock input (SCK) plus separate data in (SI) and data out (SO) lines. Access to the device is controlled through a chip select (CS) input, allowing any number of devices to share the same bus. The X25080 also features two additional inputs that provide the end user with added flexibility.

The X24164 is a CMOS 16,384 bit serial E2PROM, internally organized 2048 x 8. The X24164 features a serial interface and software protocol allowing operation on a simple two wire bus. Three device select inputs (S0–S2) allow up to eight devices to share a common two wire bus. Xicor E2PROMs are designed and tested for applications requiring extended endurance. Inherent data retention is greater than 100 years.

The X24022 is a CMOS 2048 bit serial E2PROM, internally organized 256 x 8. The X24022 features a serial interface and software protocol allowing operation on a simple two wire bus. Three address inputs allow up to eight devices to share a common two wire bus. Xicor E2PROMs are designed and tested for applications requiring extended endurance. Inherent data retention is greater than 100 years. The X24022 is available in eight pin DIP and SOIC packages.