Industrial

This document is a guide on instrument preparation and installation, involving the installation steps and precautions of two auxiliary flow panels. It also emphasizes the need to disconnect the power cord before working to avoid electrical shock hazards.

This document is the installation guide for Agilent Technologies 19251A Agilent Technologies Split/Splitless Capillary Inlet, which introduces the features and characteristics of the product, the use method, etc.

This document is an installation guide for the Agilent GPIB/RS-232 Interface Kit Accessory 19257A. It provides safety information and precautions for using the product.

The HMP8115 is a high quality NTSC and PAL decoder with internal A/D converters. It is compatible with NTSC M, PAL B, D, G, H, I, M, N, and combination N (NC) video standards. Both composite and S-video (Y/C) input formats are supported. A 2-line comb filter Y/C separator. Fast I2C interface. Two 8-bit ADCs.

This document is the instruction manual for the control module hanger of the Agilent 6850 gas chromatograph

This manual describes how to install the Agilent 6850 Gas Chromatograph Purged Packed Inlet (G2651A).

AK4524 is a 24bit 96kHz audio codec produced by Asahi Kasei. The chip has an enhanced dual-bit architecture ADC with a wide dynamic range and uses SCF technology to achieve low output noise and high jitter tolerance. AK4524 also has an input PGA and is suitable for MD, DVTR systems and musical instruments.

This note describes how to install the solvent selection valve upgrade kit into an Agilent 1100 Series binary pump. The programmable solvent selection valve combines two out of four solvents for binary pump formation or selects a different solvent for flushing the column. It cannot be used as an gradient valve. When installed the solvent selection valve can be activated from the set-up screens of your user interface.

AIC1733 is a 500mA low noise, low dropout linear regulator, and is housed in small SOT-23-5 package. When the SHDN pin is set to logic high level, the device is in the “ON” state. An internal P-MOSFET pass transistor is used to achieve 650mV low dropout voltage at 500mA load current. It offers high precision output voltage of ±2%. The quality of low quiescent current and low dropout voltage makes this device ideal for battery power applications. The internal reverse bias protection eliminates the requirement for a reverse voltage protection diode. The high ripple rejection and low noise of AIC1733 provide enhanced performance for critical applications. The noise bypass pin can be connected an external capacitor to reduce the output noise.

The AIC1570 is a 5-bit DAC that combines a synchronous PWM power regulator with an LDO and a linear controller. It is compatible with HIP6018 and provides 3 regulated voltages for the microprocessor core, clock, and GTL power. It features a simple voltage-mode PWM control, a dual N-channel MOSFET synchronous driver, and operates from +3.3V, +5V, and +12V inputs. The AIC1570 offers fast transient response, a full 0% to 100% duty ratio, ±1.0% output voltage for VCORE, and ±2.0% output voltage reference for VCLK and VGTL. It has a TTL compatible 5-bit digital-to-analog core output voltage selection with a range from 1.3V to 3.5V, adjustable in 0.1V steps from 2.1V to 3.5V and 0.05V steps from 1.3V to 2.05V. The AIC1570 also has adjustable current limit, microprocessor core voltage protection against shorted MOSFET, power good output voltage monitor, and over-voltage and over-current fault monitors. It operates with a 200KHz free-running oscillator programmable up to 350KHz.

This product is a moisture trap, which is mainly used to remove the trace amount of water present in nearly all carrier gases.

This document describes the procedure for changing the 16-Pin Bayonet Cartridge of the LabChip® 2100 bioanalyzer from Agilent Technologies. The cartridge contains 16 electrodes that make contact with the liquid in the wells of the LabChip®. If the electrodes become contaminated or damaged, the entire cartridge can be replaced. The document provides detailed instructions for removing the cartridge and the pin set.

The document describes the features and characteristics of the products.

This document is about the selection guide of ECONOLINE - DC/DC-Converter RJ and RG Series, 1 Watt, DIP14, 3kV/4kV (Single & Dual Output) products. It mainly includes the input and output voltage, current, efficiency, operating temperature and derating graph of the products.