Industrial

TLA5000 Series logic analyzers have features such as high-speed timing resolution, fast state acquisition, deep memory, and sophisticated triggering. They are suitable for identifying initialization failures, operation crashes, and intermittent operation. The TLA5000 Series logic analyzers are ideal for single-bus timing and state analysis for both first-time and experienced logic analyzer users.

This document is the TL780 series positive voltage regulator manual, which introduces the features and characteristics of the series products, including ±1% output tolerance, ±2% output tolerance, thermal shutdown, internal short circuit current limiting, pinout identical to µA7800 series, improved version of µA7800 series

The datasheet introduces the features and characteristics of the TL750L and TL751L series low-dropout voltage regulators. The series regulators have options of 5V, 8V, 10V, and 12V, and the TL751L series also has an enable (ENABLE) input. When ENABLE is high, the regulator output is in the high-impedance state. This gives the designer complete control over power up, power down, or emergency shutdown. The TL750L and TL751L series are low-dropout positive-voltage regulators specifically designed for low-power applications.

This document describes the characteristics of 378 surface mount fuses, including their nominal current, nominal voltage, cold resistance, and melting I2t values. These fuses comply with the IEC 60127-4 standard, are certified by UL, METI, and CCC, and have high environmental adaptability.

This document describes the maximum ratings and electrical characteristics of single phase 1.5 amp bridge rectifiers, including the maximum peak reverse voltage, maximum RMS voltage, maximum DC blocking voltage, and maximum average forward rectified current. It also highlights the features of the product, such as reliable low cost construction and high surge current capability.

Aluminum oxide columns are specifically designed for detailed C1-C10 hydrocarbon analysis in chemical and petrochemical industries. Due to the high selectivity of CP-Al2O3 PLOT columns, it is possible to analyze ppm to percent levels of any C1-C5 impurities, including isomers, in main stream C1-C5 products. CP-Al2O3 PLOT columns offer a higher level of analytical selectivity and efficiency compared to super-thick film non-polar liquid stationary phase columns.

This document introduces two methods for analyzing fumonisin FB1 and FB2 in food and feed samples using the Agilent 1120 Compact LC system and Agilent 6140 Single Quadrupole LC/MS system: simple extraction method (EM) and immunoaffinity column (IAC) extraction method. The results showed that both methods can successfully analyze food and feed samples. The recovery rate of the simple extraction method is higher than that of the immunoaffinity column method. The recovery rate of the EM method is between 62% and 78%, while that of the IAC method is between 42% and 64%. The simple extraction method has high cost-effectiveness, while the immunoaffinity column method has less matrix effects.

This application note introduces the use of high-resolution gas chromatography to determine the amount of ethanol and methanol in denatured fuel ethanol. The method is used on an Agilent 7890A GC system, which is coupled to Agilent MultiTechnique ChemStation software. This system offers a complete, automated solution for denatured fuel ethanol analysis.

This article discusses the importance of using furnace atomic absorption methods to determine toxic metals in water and waste, as well as the need for monitoring and regulating these elements. The article mentions the regulations set by the U.S. EPA and individual states regarding the maximum allowable concentration levels of toxic metals, and the application of furnace atomic absorption methods in EPA approved methodology.

This application note describes how to use the CRA-90 carbon rod atomizer to determine priority pollutant metals.

This article discusses the regulations and methodology for determining priority pollutant metals. It highlights the unique nature of metals as environmental and industrial pollutants and their potential detrimental effects on humans. It also describes the collaboration between federal and state agencies, private sector industrial participants, and academic research institutions in studying the sources, distribution, and environmental impact of metal pollutants.

This article introduces an automated vapor generation accessory for atomic absorption analysis. The accessory utilizes continuous flow technology to pump and mix samples and liquid reagents. It is suitable for determining low levels of elements such as arsenic, antimony, bismuth, selenium, tellurium, and tin, replacing traditional zinc metal and sodium borohydride reducing agents. The accessory simplifies the overall procedure and improves analysis efficiency.

This document mainly introduces a chemical speciation method for aluminium in environmental water bodies, which is based on bromide extraction separation and ICP-AES for measurement.