Industrial

The CMR1S-01 is a 1.0 amp super fast recovery rectifier from Central Semiconductor. It features a fast switching speed, low voltage drop, and high reliability.

This datasheet provides information on the Central Semiconductor 1.0 Amp Surface Mount Fast Recovery Silicon Rectifier, including maximum ratings, electrical characteristics, and physical dimensions.

The document describes the CENTRAL SEMICONDUCTOR 1.0 Amp Surface Mount Silicon Rectifier, which features super miniature size, special selections available, low cost, high reliability, etc. It is designed for use in various commercial, industrial, entertainment, computer, and automotive applications, especially where small size is required.

The CENTRAL SEMICONDUCTOR 1.0 Amp Surface Mount Silicon Rectifier is a high quality, well constructed, highly reliable component designed for use in all types of commercial, industrial, entertainment, computer, and automotive applications.

The DS485 is a low-power transceiver for RS-485 and RS-422 communication. It features low quiescent current, short-circuit current limitation, and thermal shutdown circuitry for protection. Both the driver and receiver support TRI-STATE outputs, and the receiver has a failsafe feature for high-level output when the input is open circuit.

The DS4812 is a dual operational amplifier from Texas Instruments that combines high slew rate and rail-to-rail output swing. The device provides 10V/µs of slew rate and 6.5 MHz of bandwidth while only consuming 1.5 mA of supply current per channel. Ideal low voltage BiFET substitute for low gain, high speed applications.

The DS4520 is a 9-bit I2C nonvolatile I/O expander plus memory. It offers users a digitally programmable alternative to hardware jumpers and mechanical switches that are being used to control digital logic nodes.

The DS4510 is a CPU supervisor with integrated 64-byte EEPROM memory and four programmable, non-volatile (NV) I/O pins. It is configured with an industry-standard I2C™ interface using either fast-mode (400kbps) or standard-mode (100kbps) communication. The I/O pins can be used as general-purpose I2C-to-parallel I/O expander with unlimited read/write capability. EEPROM registers allow the power-on value of the I/O pins to be adjusted to keep track of the system’s state through power cycles, and the CPU supervisor’s timer can be adjusted between 125ms and 1000ms to meet most any application need.

The DS4305 is a low-cost adjustable voltage reference that can be adjusted using automated techniques in the factory. It is used in power-supply calibration, threshold setting, offset nulling, bias adjusting, power amps, pressure bridges and factory-calibrated equipment.

The DS4303 is a nonvolatile (NV) sample and infinite-hold adjustable voltage reference. The reference voltage is programmed in-circuit during factory calibration/ programming. Programming the reference voltage, VOUT, is as simple as applying the desired voltage on VIN and toggling the adjust pin (ADJ) to lock the VOUT voltage level indefinitely, even if the device is power cycled. The DS4303 replaces current cumbersome factory adjustment arrangements with a low-cost solution that can be adjusted using automated techniques. In addition, the DS4303 has the ability to be readjusted after the unit has been fully assembled and tested. This results in a much more flexible manufacturing arrangement, lower inventory costs, and a quicker time-to-market.

The DS4302 is a 5-bit digital-to-analog converter (DAC) with three programmable digital outputs. The DS4302 communicates through a 2-wire, SMBus™-compatible, serial interface. The tiny 8-pin µSOP package is ideal for use in space-constrained applications. Applications include CCFL backlight brightness control and power-supply calibration.

The DS4301 is a single 32-position linear digital potentiometer with 200kΩ end-to-end resistance. The wiper setting is stored in EEPROM, so the DS4301 powers up with the last stored setting. The position of the wiper is controlled through a simple three-terminal increment/decrement interface. The DS4301 is ideal for white LED backlight brightness control. Its 8-pin µSOP package, 2.4V to 5.5V supply range, and 200kΩ end-to-end resistance are especially suited for portable, battery-powered applications such as cellular telephones and PDAs.