TEXAS Manuals

This manual provides design information for the SCPS172 Connectivity Solutions.

PCI7410 SLLA247 is TI's PC Card, UltraMedia™ and Integrated 1394a-2000 OHCI Two-Port PHY/Link-Layer Controller that is fully interoperable with FireWire™ and i.LINK™ implementations of IEEE Std 1394 and supports IEEE Std 1394a-2000 connection, short reset, multispeed concatenation, arbitration acceleration, fly-by concatenation and port disable/suspend/resume

LM124, LM124A, LM224, LM224A LM324, LM324A, LM324Y, LM2902, LM2902Q are a series of four operational amplifiers produced by TI. They have wide range supply voltages (single supply voltage 3V to 30V, dual supply voltage 3V to 26V), low supply current consumption (independent of supply voltage), common mode input voltage range includes ground (reliable detection of ground nearby voltages), low input bias and offset parameters (input offset voltage 3mV typical, A version 2mV typical; input offset current 2nA typical; input bias current 20nA typical, A version 15nA typical) and equal to maximum rated supply voltage differential input voltage range (32V, LM2902 and LM2902Q is 26V).

The TAS5713 is a 25-W, efficient, digital-audio power amplifier for driving stereo bridge-tied speakers. It features EQ and DRC, supports BTL configuration, eliminates the need for heatsinks, and supports a sample rate range of 8kHz to 48kHz.

The ADS1110 is a precision, continuously self-calibrating Analog-to-Digital (A/D) converter with differential inputs and up to 16 bits of resolution in a small SOT23-6 package. Its features include: onboard 2.048V reference, onboard PGA, onboard oscillator, 16-bit no missing codes, continuous self-calibration, single-cycle conversion, programmable data rate, I2C interface, power supply ranging from 2.7V to 5.5V, low current consumption, etc. It is suitable for applications such as portable instrumentation, industrial process control, smart transmitters, consumer goods, factory automation, temperature measurement, etc.

The DAC7632 is a 16-bit dual channel voltage output DAC from TI, it supports single or dual supply, the operating temperature range is -40°C to +85°C, it has low power, high accuracy, low noise, and is suitable for industrial process control, data acquisition systems, closed-loop servo control and other applications.

SN54HC04, SN74HC04 HEX INVERTERS are an integrated circuit produced by Texas Instruments. They have a wide power supply range (2V-6V), low power consumption (20μA), a typical delay time (8ns) and a high output drive current (±4mA).

The OPA2604 is a low distortion, low noise, wide bandwidth dual FET-input operational amplifier designed for enhanced AC performance.

This is a low-voltage audio power amplifier that can provide 250mW of continuous power at 3.3V and supports headphone driving.

This document describes the features and characteristics of the UCC2808A, a family of BiCMOS push-pull, high-speed, low-power, pulse-width modulators. The UCC2808A is qualified for automotive applications and supports customer-specific configuration control and major-change approval. It provides ESD protection exceeding 1500 V per MIL-STD-883, Method 3015, and exceeds 200 V using the Machine Model (C = 200 pF, R = 0). The UCC2808A features dual output drive stages in a push-pull configuration, a current sense discharge transistor to improve dynamic response, a typical starting current of 130 µA, and a typical run current of 1 mA. It can operate up to 1 MHz and has internal soft start. The on-chip error amplifier has a 2-MHz gain bandwidth product, and on-chip VDD clamping is provided. The output drive stages are capable of 500-mA peak-source current and 1-A peak-sink current.

This document introduces the features of the TL284xB and TL384xB series of high-performance current-mode PWM controllers, including low start-up current, trimmed oscillator discharge current, current mode operation up to 500 kHz, automatic feed-forward compensation, latching PWM for cycle-by-cycle current limiting, internally trimmed reference with undervoltage lockout, high-current totem-pole output undervoltage lockout with hysteresis, and double-pulse suppression.

This document introduces the improved versions of UC3823/UC3825 PWMs. These versions have better performance than the traditional UC3823/UC3825, including: compatible with voltage-mode or current-mode control methods, practical operation at switching frequencies to 1 MHz, 50-ns propagation delay to output, high-current dual totem pole outputs (2-A peak), trimmed oscillator discharge current, low 100-µA startup current, pulse-by-pulse current limiting comparator and latched overcurrent comparator with full cycle restart.

The datasheet is for TPA6011A4, a 3W stereo audio power amplifier with advanced DC volume control. It supports BTL and SE modes and can drive 3W/channel of continuous RMS power from -40 dB to 20 dB into a 3-ohm load.

The TPA6040A4 is a stereo audio power amplifier and DirectPath™ headphone amplifier in a thermally enhanced, space-saving, 32-pin QFN package. The speaker amplifier is capable of driving 2 W per channel continuously into 4-Ω loads at 5 V. The headphone amplifier achieves a minimum of 85 mW at 1% THD+N from a 5-V supply. It has a built-in 4-step volume control, minimizing the need for external components. It also features independent shutdown control and dedicated inputs for the speaker and headphone amplifiers.