This page provides manuals, user guides, handbooks, instructions, specification, instruction, maintenance manual for TEXAS Motherboard, Data Converters, Wireless connection, Power Management, ...
SN74AVCH245 is a low-power, high-performance, low-noise, high-speed, three-state output bus transceiver. It has a dynamic output control circuit, which can lower the output impedance when the signal is in transition, improve the load driving ability, and increase the output impedance when the signal is stable, reducing noise.
The SN74LVC2G157 is a single 2-line to 1-line data selector/multiplexer from Texas Instruments (TI) designed for 1.65-V to 5.5-V VCC operation. It features a common strobe (G) input. When the strobe is high, Y is low and Y is high. When the strobe is low, a single bit is selected from one of two sources and is routed to the outputs. The device provides true and complementary data.
The SN74LVC1G04 is a single inverter gate produced by TI. The gate works with a voltage of 1.65-V to 5.5-V and can be used for 5-V VCC operation. The device fully meets the specifications for partial power-down applications using Ioff. The Ioff circuit disables the outputs to prevent damaging current backflow through the device when it is powered down.
This document is about the datasheet of SN54BCT25244 and SN74BCT25244 25-Ω octal buffers/drivers, which are SN54BCT25244 and SN74BCT25244 respectively, and they are specially designed to enhance the performance and density of 3-state memory address drivers, clock drivers and bus-oriented receivers and transmitters.
SN54ABT543A, SN74ABT543A OCTAL REGISTERED TRANSCEIVERS WITH 3-STATE OUTPUTS is a high-speed data converter with eight bidirectional channels launched by Texas Instruments (TI). It uses advanced EPIC-IIB BiCMOS process, has the advantages of low power consumption, high ESD protection and high driving ability.
SN54ABT540 is an octal buffer/driver with 3-state outputs. It features a state-of-the-art EPIC-ΙΙB BiCMOS design that significantly reduces power dissipation. The ESD protection exceeds 2000 V per MIL-STD-883 and 200 V using the machine model. It has latch-up performance that exceeds 500 mA per JEDEC standard JESD-17. The typical output ground bounce (VOLP) is less than 1 V at VCC = 5 V, TA = 25°C. The device has high-drive outputs (-32 mA IOH, 64 mA IOL) and various package options. It is ideal for driving bus lines or buffer memory address registers.
The PT6510 series power modules are the recommended direct replacements for the PT6500 series in existing designs. These modules have the same output current rating (8A) and similar functionality. They offer improved power dissipation and efficiency, significantly reduced inrush current, and better line and load regulation.
PT4220 series power modules are a DC/DC converters designed by Texas Instruments, with an ultra-low profile (8mm) solderable copper case, and a number of preset output voltages ranging from 1.3V † up to 12V. They are fully approved for Telecom use and can be used in many other applications that require input-output isolation over an extended temperature range.
The TPIC5403 is a monolithic gate-protected power DMOS array that consists of four independent electrically isolated N-channel enhancement-mode DMOS transistors. Each transistor features integrated high-current zener diodes to prevent gate damage in the event that an overstress condition occurs. These zener diodes also provide up to 4000V of ESD protection when tested using the human-body model of a 100pF capacitor in series with a 1.5kΩ resistor.
This data sheet introduces the features and characteristics of the TPA6101A2, including external components, power supply voltage range, output power, current, gain, switch circuit, mid-rail generation, thermal protection and short circuit protection.
