Analog Devices Manuals

AD5382 is a 32-channel, 3 V/5 V, single-supply, 14-bit, voltage output DAC from Analog Devices. It features guaranteed monotonic INL error of ±4 LSB max; an on-chip 1.25 V/2.5 V, 10 ppm/°C reference; a temperature range of –40°C to +85°C; a rail-to-rail output amplifier; a power-down mode; a 100-lead LQFP (14 mm × 14 mm) package; and parallel serial (SPI®-/QSPI™-/MICROWIRE™-/DSP-compatible, featuring data readback) and I2C®-compatible user interfaces.

The AD5535 is a high-integration 32-channel, 14-bit DAC with an integrated high-voltage output amplifier. This device is targeted for optical micro-electromechanical systems. The output voltage range is programmable via the REF_IN pin. The output range is 0 V to 50 V when REF_IN = 1 V, and 0 V to 200 V when REF_IN = 4 V. Each amplifier can source 700 μA, which is ideal for the deflection and control of optical MEMS mirrors. Guaranteed monotonic. Integrated silicon diode for temperature monitoring.

The AD7304/AD7305 are quad, 8-bit DACs that operate from a single +3 V to +5 V supply, or ±5 V supplies. They feature rail-to-rail REF input to voltage output swing, 2.6 MHz reference multiplying bandwidth, internal power-on reset, SPI serial interface-compatible AD7304, and fast parallel interface AD7305.

AD8278/AD8279 is a low power, wide supply range, low cost difference amplifier with a gain of G = ½

This document is the datasheet of AD9240. It introduces the characteristics of AD9240, such as 14-bit, 10msps, single power supply.

AD8556 is a digitally programmable sensor signal amplifier with EMI filters from Analog Devices (ADI). It has a wide operating temperature range of -40°C to +140°C, low input offset voltage, low input offset voltage drift, high CMRR, and can be programmed via a single-wire serial interface. It is suitable for applications such as automotive sensors, pressure and position sensors, precision current sensing and strain gauges.

AD823 is a single-supply, 16MHz, rail-to-rail FET input amplifier produced by Analog Devices, with a power supply voltage range from 3V to 36V, an output voltage range from ground to supply voltage, a 500pF output capacitance load capability, an output current of 15mA, an output voltage swing of 16MHz, a low distortion of -108dBc, a low noise of 16nV/√Hz, and no phase inversion, which can be applied to battery-powered precision instruments, photodiode preamplifiers, active filters, 12-bit to 16-bit data acquisition systems, and medical devices.

The ADL5500 is a mean-responding power detector for use in high frequency receiver and transmitter signal chains from 100 MHz to 6 GHz. It features true rms response, excellent temperature stability, and high input dynamic range.

The AD7904/AD7914/AD7924 are respectively, 8-bit, 10-bit, and 12-bit, high speed, low power, 4-channel, successive-approximation ADCs. The parts operate from a single 2.7 V to 5.25 V power supply and feature throughput rates up to 1 MSPS. The AD7904/AD7914/AD7924 feature flexible power/serial clock speed management, no pipeline delays, up to 70 dB SNR, SPI/QSPI/MICROWIRE/DSP compatible high speed serial interface, and 0.5 µA maximum shutdown mode.

The AD2S1200 is a complete 12-bit resolution tracking resolver-to-digital converter, integrating an on-board programmable sinusoidal oscillator that provides sine wave excitation for resolvers. An external 8.192 MHz crystal is required to provide clock to the oscillator.

The AD603 is a low noise, voltage controlled amplifier for use in RF and IF AGC systems. It provides accurate, pin-selectable gains of −11 dB to +31 dB with a bandwidth of 90 MHz or +9 dB to 51+ dB with a bandwidth of 9 MHz. Any intermediate gain range may be arranged using one external resistor. The input referred noise spectral density is only 1.3 nV/√Hz, lower than any other similar product.

The AD7398/AD7399 is a 12-bit/10-bit, serial-input quad DAC designed to operate from a single or dual power supply.