Industrial

E2K-C Adjustable Long-distance Sensor detects both metallic and nonmetallic objects (water, plastic, etc.).

MHB series are double metallized polypropylene film capacitors, with features of high current, high voltage, multiple lead styles (2, 4, lugs) and small size.

K4D64163H is 67,108,864 bits of hyper synchronous data rate Dynamic RAM organized as 4 x1,048,576 words by 16 bits, fabricated with SAMSUNG’s high performance CMOS technology. Synchronous features with Data Strobe allow extremely high performance up to 1.2GB/s/chip. I/O transactions are possible on both edges of the clock cycle. Range of operating frequencies, programmable burst length and programmable latencies allow the device to be useful for a variety of high performance memory system applications.

The 33887 is a 5.0 A H-Bridge with Load Current Feedback making it ideal for closed-loop DC motor control. The IC incorporates internal control logic, charge pump, gate drive, and low RDS(ON) MOSFET output circuitry.

The LT1158 is a half-bridge N-channel power MOSFET driver that drives the gate of the top MOSFET above V+. It operates at supply voltages from 5V to 30V, with 150ns transition times driving 3000pF. It has a peak driver current of over 500mA, adaptive non-overlap gate drives, continuous current limit protection, automatic shutdown and retry capability, a built-in charge pump for DC operation, built-in gate voltage protection, and is compatible with current-sensing MOSFETs. It has TTL/CMOS input levels and a fault output indication.

The LTC1325 is a microprocessor-controlled battery management system that features fast charging, flexible current regulation, battery voltage, temperature, and charge time fault protection, etc.

The ADuC834 is a complete smart transducer front end, integrating two high resolution ADCs, an 8-bit MCU, and program/data Flash/EE memory on a single chip.

The MAX195 is a 16-bit successive-approximation analog-to-digital converter (ADC) that combines high speed, high accuracy, low power consumption, and a 10µA shutdown mode. Internal calibration circuitry corrects linearity and offset errors to maintain the full rated performance over the operating temperature range without external adjustments. The capacitive-DAC architecture provides an inherent 85ksps track/hold function. The MAX195, with an external reference (up to +5V), offers a unipolar (0V to VREF) or bipolar (-VREF to VREF) pin-selectable input range. Separate analog and digital supplies minimize digital-noise coupling. The chip select (CS) input controls the three-state serial-data output. The output can be read either during conversion as the bits are determined, or following conversion at up to 5Mbps using the serial clock (SCLK). The end-of-conversion (EOC) output can be used to interrupt a processor, or can be connected directly to the convert input (CONV) for continuous, full-speed conversions. The MAX195 is available in 16-pin DIP, wide SO, and ceramic sidebraze packages.

The MAX548A/MAX549A/MAX550A are serial, 8-bit voltage-output digital-to-analog converters (DACs) that operate from a single +2.5V to +5.5V supply. Their ±1LSB TUE specification is guaranteed over temperature. Operating current (supply current plus reference current) is typically 75µA per DAC with VDD = 2.5V. In shutdown, the DAC is disconnected from the reference, reducing current drain to less than 1µA. The MAX548A/MAX549A allow each DAC to be shut down independently. The 10MHz, 3-wire serial interface is compatible with SPI™/QSPI™ and Microwire™ interface standards. Double-buffered inputs provide flexibility when updating the DACs; the input and DAC registers can be updated individually or simultaneously. The MAX548A is a dual DAC with an asynchronous load input; it uses VDD as the reference input. The MAX549A is a dual DAC with an external reference input. The MAX550A is a single DAC with an external reference input and an asynchronous load input. The MAX548A/MAX549A/MAX550A’s low power consumption and small µMAX and DIP packages make these devices ideal for portable and battery-powered applications.

This document is about the specification of eZ80L92 chip

The ADC124S101 is a low-power, four-channel CMOS 12-bit analog-to-digital converter with a high-speed serial interface.

LW P4SG Hyper PointLED® is a long life Enhanced optical Power LED (ThinGaN®) with no lead (Pb) and is RoHS compliant. It can be mounted from the bottom or top, and is ideal for extremely flat backlighting.

This datasheet provides detailed information on the EPCOS LBC series inductor products, including rated current, rated inductance, construction, features, applications, terminals, marking, delivery mode, dimensional drawing, characteristics and ordering codes.