Industrial

The AM26LV32 is a BiCMOS, quadruple, differential line receiver with 3-state outputs, designed to be similar to TIA/EIA-422-B and ITU Recommendation V.11 receivers, but with a reduced common-mode voltage range due to reduced supply voltage. The device is optimized for balanced bus transmission at switching rates up to 32 MHz. The enable function is common to all four receivers and offers a choice of active-high or active-low inputs. The 3-state outputs permit direct connection to a bus-organized system. Each device features receiver high input impedance and input hysteresis for increased noise immunity, and input sensitivity of ±200 mV over a common-mode input voltage range from −0.3 V to 5.5 V. When the inputs are open circuited, the outputs are in the high logic state. This device is designed using the Texas Instruments (TI) proprietary LinIMPACT-C60 technology, facilitating ultra-low power dissipation.

LMH6714/6720/6722 is a high performance video op amp from National. It provides 400MHz bandwidth and 1800V/µs slew rate with only 5.6mA power consumption. This product series is ideal for broadcast quality video systems. Its small size, low power, low noise and distortion also make it suitable for portable RF applications.

The ICL7665 is a low-power, high-precision voltage monitor chip produced by Maxim. It uses externally programmable thresholds and hysteresis outputs for µP voltage monitoring, low battery detection, power failure and brownout detection, battery backup switching and power supply fault monitoring.

The AP8801 is a 500mA LED step-down converter designed to drive LEDs with a constant current. It can drive up to thirteen LEDs, depending on the forward voltage of the LEDs, in series from a voltage source of 8V to 48V.

The EL7554 is a full-feature synchronous 4A step-down regulator capable of up to 96% efficiency

This data sheet provides detailed information on the PS9821-1 and PS9821-2 high CMR, 15 Mbps open collector output type 8-pin SSOP (SO-8) 3.3V high-speed photocouplers.

The MAX1703 is a high-efficiency, low-noise, step-up DC-DC converter intended for use in battery-powered wireless applications. It uses a synchronous-rectified pulse-width-modulation (PWM) boost topology to gen- erate a 2.5V to 5.5V output from battery inputs, such as one to three NiCd/NiMH cells or one Li-Ion cell. The device includes a 2A, 75mΩ, N-channel MOSFET switch and a 140mΩ, P-channel synchronous rectifier. With its internal synchronous rectifier, the MAX1703 delivers up to 5% better efficiency than similar nonsyn- chronous converters. It also features a pulse-frequency- modulation (PFM) low-power mode to improve efficiency at light loads, and a 1µA shutdown mode. The MAX1703 comes in a 16-pin narrow SO package and includes an uncommitted comparator that generates a power-good or low-battery-warning output. It also contains a linear gain block that can be used to build a linear regulator. For lower-power outputs and a smaller package, refer to the MAX1700/MAX1701. For dual outputs (step-up plus linear regulator), refer to the MAX1705/MAX1706. For an on-board analog-to-digital converter, refer to the MAX848/MAX849. The MAX1703 evaluation kit is available to speed designs.

The MAX823/MAX824/MAX825 are microprocessor (μP) supervisory circuits from MAXIM that combine reset output, watchdog, and manual reset input functions in 5-pin SOT23 and SC70 packages. They significantly improve system reliability and accuracy compared to separate ICs or discrete components. The MAX823/MAX824/MAX825 are specifically designed to ignore fast transients on VCC. Seven preprogrammed reset threshold voltages are available (see Reset Threshold Table). All three devices have an active-low reset output, which is guaranteed to be in the correct state for VCC down to 1V. The MAX823 also offers a watchdog input and manual reset input. The MAX824 offers a watchdog input and a complementary active-high reset. The MAX825 offers a manual reset input and a complementary active-high reset. The Selector Guide explains the functions offered in this series of parts.

The document describes the features and characteristics of the Littelfuse SL1003A series gas discharge tubes, including compliance with the RoHS standard, low insertion loss, surface mountability, 5kA surge capability, GHz working frequency, excellent response speed, 10/700 6kV capability, and 2000 Amp 2/10μs surge rating.

DS1859 Dual, Temperature-Controlled Resistors with Internally Calibrated Monitors

The L7800A series of three-terminal positive regulators is available in TO-220, TO-220FP, TO-220FM and D2PAK packages and several fixed output voltages, making it useful in a wide range of applications.

CEAG AG/FRIWO Group is a leading global provider of power supplies, offering high-quality products and innovative design.

CLC031A is a video deserializer/descrambler produced by Cirrus Logic, which supports SMPTE292M, 259M, and 344M standards

TSOP348.. is a miniature infrared receiver module produced by Vishay company. It has the characteristics of small size, strong anti-interference ability, and supports 3V power supply. It can be used for 30, 33, 36, 36.7, 38, 40, 56kHz frequency infrared remote control systems.