Industrial

The LX8580 is a high-performance, very low dropout voltage regulator, designed for use with advanced microprocessors. This product can be used with separate voltage supplies for the control and power sections, allowing a power section dropout voltage as low as 100mV. The LX8580 can also be used in a single voltage supply configuration, with a dropout performance similar to that of the LX8584 (1.3V at 7A). The LX8580 is supplied in a five-terminal TO-220 package.

This is a 1500W surface mount transient voltage suppressor that features RoHS compliance, is suitable for surface mount applications to optimize board space, has a low profile package, built-in strain relief, glass passivated junction, low inductance, excellent clamping capability, repetition rate (duty cycle) of 0.05%, fast response time (typically less than 1.0ps from 0 Volts to BV min.), typical IR less than 1µA above 10V and high temperature soldering (250℃/10 seconds at terminals).

DD 300…DD 1800 Fast Switching High Voltage Si-Rectifiers are highly reliable semiconductor devices which are used in circuits to achieve DC. These devices are characterized by high reliability, high temperature stability, low RON and low power consumption.

LTC694-3.3/LTC695-3.3 are 3.3V microprocessor supervisory circuits that provide features such as power-on reset, battery backup, RAM write protection, power failure warning, and watchdog timing.

The LTC3806 is a current mode synchronous flyback controller that drives N-channel power MOSFETs and requires very few external components. It is intended for medium power applications where multiple outputs are required. Synchronous rectification provides higher efficiency and improved output cross regulation than nonsynchronous converters. The IC contains all the necessary control circuitry including a 250kHz oscillator, precision undervoltage lockout circuit with hysteresis, gate drivers for primary and synchronous switches, current mode control circuitry and soft-start circuitry. Programmable soft-start reduces inrush currents. This makes it easier to design compliant Power Over Ethernet supplies. Low start-up current reduces power dissipation in the start-up resistor and reduces the size of the external start-up capacitor. The LTC3806 is available in a 12-pin, exposed pad DFN package.

The LTC3455 is a high-efficiency DC/DC converter that can be used in portable devices. It features two synchronous step-down DC/DC converters, a USB power controller, a full-featured Li-Ion battery charger, a Hot Swap output, a low-battery indicator, and numerous internal protection features.

The TL594 is a pulse-width modulation control circuit produced by Unisonic Technologies Co., Ltd. It is compatible with TL494 and has an output current of up to 200mA. It can be single-ended or push-pull output, and has internal reference power, variable dead time, undervoltage lockout and other functions.

This product is a high side current sense monitor that can convert the high side voltage generated across a current shunt resistor into a proportional output current. A user-defined output resistor scales the output current into a ground-referenced voltage. The wide input voltage range of 2.5V to as low as 2.5V makes it suitable for a range of applications. A minimum operating current of just 4µA, combined with its SOT23 package, makes it a unique solution, suitable for portable battery equipment.

The ZXCL200 is a very small 2 volt regulator designed for use in low power and severely space limited applications. Supply current is minimised with a ground pin current of only 40µA at full 100mA load. Logic control allows the device to be shut down, consuming typically less than 10nA. These features make it ideal for battery powered applications where power economy is critical. The part has been designed with space sensitive systems in mind. It is available in the ultra small SC70 package, which is half the size of other SOT23 based regulator devices.

This is the user manual for the Z89302/04/06 digital television controller, which introduces the functions and usage of the controller.

The AD9071 is a monolithic sampling analog-to-digital converter with an on-chip track-and-hold circuit and TTL/CMOS digital interfaces. The product operates at a 100 MSPS conversion rate with outstanding dynamic performance over its full operating range. The ADC requires only a single 5 V supply and an encode clock for full performance operation. The digital outputs are TTL compatible. Separate output power supplies are not required.