Industrial

The MC14093B is a low-power Schmitt trigger manufactured by Motorola.

SN54HC664, SN54HC665, SN74HC664, SN74HC665 are 8-bit bus transceivers with parity function produced by Texas Instruments

The MC14043B and MC14044B quad R-S latches are constructed with MOS P-channel and N-channel enhancement mode devices in a single monolithic structure. Each latch has an independent Q output and set and reset inputs. The Q outputs are gated through three-state buffers having a common enable input. The outputs are enabled with a logical “1” or high on the enable input; a logical “0” or low disconnects the latch from the Q outputs, resulting in an open circuit at the Q outputs.

B1035CL is a diode produced by Schneider Electric. It uses the Schottky barrier principle in a large area metal-to-silicon power diode. It features epitaxial construction with oxide passivation and metal overlay contact.

IRF9230 is a high voltage power MOSFET transistor produced by International Rectifier company. It has very low on-state resistance, high transconductance, superior reverse energy and diode recovery dv/dt capability.

This document describes the features and characteristics of PEP-3R-160 PEP-3R series phase shifters, including frequency range, phase shift range, insertion loss, etc.

The MB90495-series with FULL-CAN interface and FLASH ROM is especially designed for automotive and industrial applications

This document is the datasheet of Intersil XDCP series single-chip digitally controlled potentiometer X9111, which introduces the function characteristics, usage method and other information of the product in detail.

The MB89490 series is a general-purpose version of the F2MC-8L family, which consists of proprietary 8-bit single-chip microcontrollers. In addition to a compact instruction set, the general-purpose single-chip microcontroller contains various peripheral functions such as a 21-bit timebase timer, watch prescaler, PWM timer, 8/16-bit timer/counter, remote receiver circuit, LCD controller/driver, external interrupt 0 (edge), external interrupt 1 (level), 10-bit A/D converter, UART/SIO, SIO, I2C, and watchdog timer reset. The MB89490 series is suitable for compact disc/radio receiver controllers as well as a wide range of applications for consumer products.

The SY100S838/L is a low skew (÷1, ÷2/3) or (÷2, ÷4/6) clock generation chip designed explicitly for low skew clock generation applications. The internal dividers are synchronous to each other, therefore, the common output edges are all precisely aligned. The devices can be driven by either a differential or single-ended ECL or, if positive power supplies are used, PECL input signal. In addition, by using the VBB output, a sinusoidal source can be AC- coupled into the device. If a single-ended input is to be used, the VBB output should be connected to the CLK input and bypassed to ground via a 0.01µF capacitor. The VBB output is designed to act as the switching reference for the input of the SY100S838/L under single- ended input conditions. As a result, this pin can only source/sink up to 0.5mA of current. The Function Select (FSEL) input is used to determine what clock generation chip function is. When FSEL input is LOW, SY100S838/L functions as a divide by 2 and by 4/6 clock generation chip. However, if FSEL input is HIGH, it functions as a divide by 1 and by 2/3 clock chip. The common enable (EN) is synchronous so that the internal dividers will only be enabled/disabled when the internal clock is already in the LOW state. This avoids any chance of generating a runt clock pulse on the internal clock when the device is enabled/disabled as can happen with an asynchronous control. An internal runt pulse could lead to losing synchronization between the internal divider stages.

This document provides information on a new product under development or evaluation. The product is a multifunctional monitor that includes features for screen size and centering auto setup, measurements of horizontal sync, vertical sync, and video timing signals up to 100MHz pixel clock. It has a character ROM font, allowing for the display of custom characters and text. The product also features an I2C bus MCU interface and five 8-bit PWM DAC outputs.

The STS8NF30L is a low voltage high current N-channel power MOSFET produced by STMicroelectronics. Its maximum voltage is 30V and its minimum on-resistance is 0.018 ohms. It is packaged in SO-8.

stlc1511 is a new wide dynamic range analog front end chip from st. it uses a 14-bit nyquist rate da converter and a programmable gain amplifier. it supports 0~-32db transmit gain and 0~40db receive gain. it integrates a phase-locked loop with an external LC or crystal oscillator. the power consumption is only 300mw.