Industrial

The CAT5251 is four Digitally Programmable Potentiometers (DPPs™) integrated with control logic and 16 bytes of NVRAM memory. Each DPP consists of a series of resistive elements connected between two externally accessible end points. The tap points between each resistive element are connected to the wiper outputs with CMOS switches. A separate 8-bit control register (WCR) independently controls the wiper tap switches for each DPP. Associated with each wiper control register are four 8-bit non-volatile memory data registers (DR) used for storing up to four wiper settings. Writing to the wiper control register or any of the non-volatile data registers writes the data to the NVRAM memory.

HER101 THRU HER108 are 1.0 Amp High Efficient Rectifiers with ratings from 50 to 1000 Volts. Products feature high surge current capability, high reliability, low forward voltage drop and high current capability.

SRC1202K is a NPN Silicon Transistor with built-in bias resistors. It is suitable for switching application, interface circuit and driver circuit application.

KSR2005 is a PNP type transistor produced by Fairchild Semiconductor Corporation. It features a high current conduction, low voltage, low power consumption and high frequency. Therefore, it is widely used in switching circuits, inverters, interface circuits and driver circuits.

The SPX2940 is a 1A, accurate voltage regulators with a low drop out voltage of 280mV (typical) at 1A.

This document describes the features and characteristics of the PK(PD,PE,KK)25F THYRISTOR MODULE produced by SanRex at 50 Seaview Blvd. Port Washington, NY 11050-4618.

The SPX1582 is a 3A low dropout regulator with an extremely low dropout voltage. The adjustable version requires only two external resistors to set the output voltage. The fixed version has a preset output of 3.3V, 2.8V or 2.5V and does not require any external resistors. The SPX1582 features a low dropout of 400mV(Typ.) and offers fast transient response. This device is suitable for Pentium applications requiring 2.8V, 2.5V from 3.3V ATX power supplies, where a low current input voltage 1V greater than the output voltage is needed. With an external sense pin the load regulation is less than 1mV. This device is an excellent choice for the use of powering low voltage microprocessors that require a lower dropout, fast transient response to regulate from 3.3V and 5V supplies. The SPX1582 is also an excellent choice as a post regulator for switching supplies applications. The SPX1582 offers protection against over-current faults, reversed input polarity, over temperature operation and positive and negative transient voltage. The SPX1582 is offered in a 5 pin TO-220 and TO-263 compatible with industry standard 5-terminal regulators.

The SPX1004 is a 2-terminal bandgap precision voltage reference that provides a stable fixed output voltage of 1.2V and 2.5V with a tolerance of ±10mV for SPX1004-1.2 and ±20mV for SPX1004-2.5. Design, process and precision on chip trimming yield a very low tempera- ture coefficient of 25 ppm/°C. The SPX1004 can be used as a pin-to-pin replacement for the LT1004, LM1004 or AS1004. The SPX1004 is available in SOT-89, NSOIC-8 and TO-92 packages over the operating temperature range of 0°C to 70°C.

This data sheet is about Motorola MC54/74HC573A data sheet, including pin definition, function characteristics and other information.

The SP504 is a single chip device that supports eight (8) physical serial interface standards for Wide Area Network Connectivity. It is fabricated using a low power BiCMOS process technology, and incorporates a Sipex patented (5,306,954) charge pump allowing +5V only operation. Seven (7) drivers and seven (7) receivers can be configured via software for any of the above interface modes at any time. The SP504 is suited for DTE-DCE applications. The SP504 requires only one external resistor per V.35 driver for compliant V.35 operation.

This document provides specifications and features of OneNAND256 flash memory, including different models with voltage, temperature range, and packaging options.

This document introduces the specifications of three Samsung OneNAND flash memory products (1GB, 2GB and 4GB)

The SN74LVCU04A is a hex inverter designed for 1.65-V to 3.6-V VCC operation. It contains six independent inverters with unbuffered outputs and performs the Boolean function Y = A. Inputs can be driven from either 3.3-V or 5-V devices. This feature allows the use of these devices as translators in a mixed 3.3-V/5-V system environment.

This document is the user manual of the SN74LVC16646 16-bit bus transceiver and register