Industrial

This document introduces the features and characteristics of ST's L6384E high-voltage half bridge driver product, including high voltage rail range, driver current capability, switching time, logic input type, dead time setting, under voltage lockout, integrated bootstrap diode, and capacitor clamping.

The L6375D is a monolithic intelligent power switch in BCDmultipower technology, for driving inductive or resistive loads with controlled output voltage slew rate and short-circuit protection. It features a 0.5 A output current, 8 V to 35 V supply voltage range, internal current limiting, thermal shutdown, open ground protection, internal negative voltage clamping for fast demagnetization, differential inputs with large common mode range and threshold hysteresis, undervoltage lockout with hysteresis, open load detection, two diagnostic outputs, output status LED driver, non-dissipative short-circuit protection, immunity against burst transient (IEC 61000-4-4), and ESD protection (human body model ±2 kV).

The device is specifically designed to provide all the necessary features to implement a single phase energy meter without any other active component.

STUSB03E is a USB transceiver produced by ST company. It supports USB 2.0 protocol with a speed of up to 12Mbps. It supports low power consumption and low voltage power supply, and is suitable for PDAs, MP3 players and mobile phones.

The L9524C is a control IC for up to six glow plugs of diesel engines. The glow plugs are switched by up to four external PWM-controlled N-channel Power MOSFETs or a single relay in high-side configuration. Supply voltage, battery voltage, junction temperature, switches, currents through the glow plugs, and charge pump voltage are monitored. A two-wire interface is used to communicate with the diesel engine management system.

The L6375S is a monolithic intelligent power switch with a high-side driver function. It has a 0.5A output current, a supply voltage range of 8V to 35V, internal current limiting and thermal shutdown, open ground protection, internal negative voltage clamping for fast demagnetization, differential inputs with a large common mode range and threshold hysteresis, undervoltage lockout with hysteresis, open load detection, two diagnostic outputs, an output status LED driver, non-dissipative short-circuit protection, immunity against burst transient (IEC 61000-4-4), and ESD protection.

The TDE1708DFT intelligent power switch has a low side or high side switch configuration, a supply voltage range of 6V to 48V, overload and short circuit protections, internal voltage clamping, supply and output reversal protection, thermal shutdown, GND and VS open wire protection, adjustable delay at switch on, indicator status LED driver, +5V regulated aux. voltage, and high burst immunity.

The L6386E is a high-voltage high and low side driver with features such as high voltage rail, dV/dt immunity, driver current capability, fast switching times, CMOS/TTL inputs, and under-voltage lockout.

The L6387E is a high-voltage high and low side driver from ST company, with 600V voltage rail, dV/dt immunity ±50V/nsec, 400mA source, 650mA sink, 50/30nsec rise/fall time, CMOS/TTL Schmitt trigger inputs, internal bootstrap diode, outputs in phase with inputs, interlocking function and other features.

The L6388E is a high-voltage high and low side driver with features such as high-voltage rail, dV/dt immunity, and high driver current capability.

This is a datasheet for VNI4140K Quad high-side smart power solid-state relay. The relay has an output current of 0.7 A per channel, shorted load protections, and temperature protections.

The VN808-32-E is an eight-channel high side driver with VCC/2 compatible input, junction overtemperature protection, case overtemperature protection, current limitation, shorted load protection, undervoltage shut-down, protection against loss of ground, very low stand-by current and compliance to 61000-4-4 IEC test up to 4 kV.

The L6390 is a high-voltage half bridge driver for N-channel Power MOSFETs or IGBT. It features a high-voltage rail, integrated operational amplifier and comparator for advanced current sensing and fault protection.

The L6392 is a high-voltage high and low side driver with features including high voltage rail up to 600V, dV/dt immunity of ±50V/nsec, driver current capability of 290mA source - 430mA sink, fast switching times, 3.3V and 5V TTL/CMOS inputs, integrated bootstrap diode, operational amplifier for current sensing, adjustable dead-time, interlocking function, compact layout, and bill of material reduction.

L6393 is a high-voltage half-bridge gate driver with features such as high voltage rail, dV/dt immunity, high driver current capability, fast switching times, etc. It is suitable for motor drivers in home appliances, factory automation, industrial drives and fans, HID ballasts, and power supply units.