Industrial

This document describes the features and characteristics of Quad-Channel Digital Isolators ADuM1400/ADuM1401/ADuM1402, including low power operation, 5V and 3V operation, bidirectional communication, high temperature operation, high data rate, precise timing characteristics, etc.

The ADuM1310/ADuM1410 are triple- and quad-channel unidirectional digital isolators that operate in either a 5 V or 3 V supply and provide up to 10 Mbps data rate.

This document introduces the analysis methods of low molecular weight resins from Agilent Technologies, Inc., including molecular weight distribution, composition, crystallinity and aggregation.

Fast separations of intact and reduced monoclonal antibodies (mAbs) were achieved with the use of an Agilent ZORBAX Rapid Resolution High Definition (RRHD) 300 diphenyl reversed-phase column and optimized chromatographic conditions. The unique diphenyl phase and robust rapid resolution high definition column technology, in combination with optimized gradient conditions, provided ultra fast separations and delivered excellent peak shapes demonstrating utility for high throughput mAb charac terizations.

This application note demonstrates the use of Agilent's Mx3005P QPCR System and the resDNASEQ Quantitative CHO DNA Kit (Life Technologies) for the detection of residual CHO host cell DNA. This method produces more specific, more sensitive, and faster results than traditional blot hybridization methods.

The TPS2834 and TPS2835 are MOSFET drivers for synchronous-buck power stages. These devices are ideal for designing a high-performance power supply using a switching controller that does not include suitable on-chip MOSFET drivers. The drivers are designed to deliver minimum 2-A peak currents into large capacitive loads. The high-side driver can be configured as ground-reference or as floating-bootstrap. An adaptive dead-time control circuit eliminates shoot-through currents through the main power FETs during switching transitions, and provides high efficiency for the buck regulator. The TPS2834 and TPS2835 have additional control functions: ENABLE, SYNC, and CROWBAR. Both high-side and low-side drivers are off when ENABLE is low. The low-side driver is configured as a nonsynchronous-buck driver when SYNC is low.

This application note demonstrates the applicability of SFC for typical polymer additives using the Agilent 1260 Infinity Analytical SFC System in combination with an Agilent 6130 Single Quadrupole LC/MS System.

The document provides an overview of the features and characteristics of TP products.

This Application Note demonstrates that stringent sensitivity requirements for the detection of potentially harmful primary aromatic amines can be fulfilled when using an Agilent 1290 Infinity LC System equipped with the 1290 large volume injection kit. This enables the Agilent 1290 Infinity Autosampler for injection volumes up to 120 μL for sample enrichment on the column. A high sensitivity 60-mm Max-Light flow cell in the Agilent 1290 Infinity Diode Array Detector gives additional detection sensitivity.

TOPSwitch-II family of three terminal off-line PWM switch incorporates all functions necessary for a switched mode control system into a three terminal monolithic IC: power MOSFET, PWM controller, high voltage start up circuit, loop compensation and fault protection circuitry.

This document describes a comprehensive method for profiling free and conjugated estrogens using capillary electrophoresis-time of flight-mass spectrometry. The method is sensitive and robust.

8-bit analog-to-digital converters with serial control

This article introduces two methods for detecting toxins in wheat using different sample preparation methods, a modified QuEChERS method and the Agilent Bond Elut mycotoxin SPE method. The results showed that both methods can effectively detect toxins in wheat, but the modified QuEChERS method is faster and uses less solvent and sorbent.

This datasheet introduces the TLC3544 and TLC3548 5-V analog, 3-/5-V digital, 14-bit, 200-KSPS, 4-/8-channels serial analog-to-digital converters with 0-5 V (pseudodifferential) inputs.