TEXAS Manuals

This document is about TLC2272 and TLC2274 datasheet, introduces the features and characteristics of the two devices.

The LM101A, LM201A, and LM301A are high-performance operational amplifiers featuring very low input bias current and input offset voltage and current to improve the accuracy of high-impedance circuits using these devices. The high common-mode input voltage range and the absence of latch-up make these amplifiers ideal for voltage-follower applications. The devices are protected to withstand short circuits at the output. The external compensation of these amplifiers allows the changing of the frequency response (when the closed-loop gain is greater than unity) for applications requiring wider bandwidth or higher slew rate. A potentiometer may be connected between the offset-null inputs (N1 and N).

This document describes the features and characteristics of Harris Semiconductor SCHS223A, including typical propagation delay, exceeding 2kV ESD protection, SCR-Latchup-Resistant CMOS process and circuit design, balanced propagation delays, etc.

SN74LVC541 is an 8-channel 3-state output buffer/driver produced by TI company. It is suitable for 2.7V to 3.6V VCC power supply, and has the characteristics of low power consumption, high speed, and high anti-interference.

This document is about the SN74LVC3G04 triple inverter. It is designed for 1.65-V to 5.5-V VCC operation and has a maximum tpd of 4.1 ns. At 3.3 V, the output drive current can reach ±24 mA and it supports partial power-down mode operation.

This datasheet lists the specifications of the SN74LVC2G74 single positive-edge triggered D-type flip-flop, including package type, package size, input voltage range, output voltage range, output drive capability, power consumption, etc.

This datasheet provides detailed information on the SN74LVC2G38, including its features, specifications, and ordering information.

This document describes the features and characteristics of the SCES337G model. The product supports 2V to 5.5V VCC operation and has low output ground bounce and high output VOH undershoot. The outputs are disabled during power up and power down with inputs tied to VCC. The product supports mixed-mode voltage operation on all ports and has latch-up performance exceeding 100mA and ESD protection exceeding 2000V.

This document contains packaging information and orderable device status for supplier 74365. The document lists detailed information about different models of the product, including package type, number of pins, package quantity, etc.

The SN54LV541A, SN74LV541A OCTAL BUFFERS/DRIVERS WITH 3-STATE OUTPUTS is an integrated circuit manufactured by TI. The chip uses the EPIC(Enhanced-Performance Implanted CMOS) process, has a 2-V to 5.5-V VCC operating voltage, and has a latch-up performance of 250 mA per JESD 17 and an ESD protection of 200 V per MIL-STD-883, Method 3015.

SN54BCT244, SN74BCT244 are octal buffers/drivers with 3-state outputs from Texas Instruments Incorporated. These octal buffers and line drivers are designed specifically to improve both the performance and density of 3-state memory address drivers, clock drivers, and bus-oriented receivers and transmitters.

The REG103 is a family of low-noise, low-dropout, linear regulators with low ground pin current. Its new DMOS topology provides significant improvement over previous designs, including low-dropout voltage (only 115mV typ at full load), and better transient performance. In addition, no output capacitor is required for stability, unlike conventional low-dropout regulators that are difficult to compensate and require expensive low ESR capacitors greater than 1µF. Typical ground pin current is only 1mA (at IOUT = 500 mA) and drops to 0.5µA in not enabled mode. Unlike regulators with PNP pass devices, quiescent current remains relatively constant over load variations and under dropout conditions. The REG103 has very low output noise (typically 33µVrms for VOUT = 3.3V with CNR = 0.01µF), making it ideal for applications requiring high precision and low noise.

CDC2510 is a 3.3V low-skew low-jitter phase-lock loop clock driver designed for synchronous DRAM applications. It uses a PLL to precisely align, in both frequency and phase, the feedback (FBOUT) output to the clock (CLK) input signal. The CDC2510 operates at 3.3V VCC and provides integrated series-damping resistors that make it ideal for driving point-to-point loads. A bank of ten outputs provides ten low-skew, low-jitter copies of CLK. Output signal duty cycles are adjusted to 50 percent, independent of the duty cycle at CLK. All outputs can be enabled or disabled via a single output enable input. When the G input is high, the outputs switch in phase and frequency with CLK; when the G input is low, the outputs are disabled to the logic-low state. Unlike many products containing PLLs, the CDC2510 does not require external RC networks. The PLL's loop filter is included on-chip, minimizing power consumption and cost.

SCHS122G is a digitally controlled analog switch developed by Harris Semiconductor. It uses silicon gate CMOS technology and operates in a similar way to LSTTL, with low power consumption. The switch voltage range is 0V to 10V, and the load voltage range is ±5V. It has low resistance, low crosstalk, and fast switching.

This data sheet is applicable to CD54/74AC299, CD74AC323, CD54/74ACT299, and CD54ACT323. The CD54AC323 and CD74ACT323 were not acquired from Harris Semiconductor. Data sheet acquired from Harris Semiconductor SCHS288.