TEXAS Manuals

TLV5614 is a quadruple 12-bit voltage output digital-to-analog converter (DAC) with a flexible 4-wire serial interface.

The TLV5606 is a 10-bit voltage output digital-to-analog converter (DAC) with a flexible 4-wire serial interface. It can be used in a wide range of applications, including digital servo control loops, digital offset and gain adjustment, industrial process control, machine and motion control devices, and mass storage devices.

This document introduces the features and characteristics of the DIT4096 digital audio transmitter. The product complies with AES-3, IEC-60958 and EIAJ CP1201 interface standards, supports sampling rates up to 96kHz, supports mono mode operation, integrates differential line driver, has a flexible audio serial interface, supports I2S, left-aligned and right-aligned data formats, supports software mode and hardware mode, and supports CRC code generation.

MSP430x22x2, MSP430x22x4 Mixed Signal Microcontrollers are low-power, low-voltage microcontrollers with ultrafast wake-up time from standby mode and a 16-bit RISC architecture. The product supports various clock configurations and communication interfaces, and is equipped with a 10-bit A/D converter and configurable operational amplifiers. Additionally, it features security protection to prevent program reading.

The TLV5604 is a quadruple 10-bit voltage output digital-to-analog converter (DAC).

TPS65820 is a single-cell lithium-ion battery and power management IC from ti, which has host interface, battery charger, integrated power supply and other functions.

This datasheet introduces the DAC9881 device from TI. It is a 18-bit single-channel low-noise voltage-output digital-to-analog converter. The device features 18-bit monotonicity, excellent linearity, very low noise and fast settling time. The device's on-chip precision output amplifier allows rail-to-rail output swing to be achieved over the full supply range of 2.7V to 5.5V. The device supports a standard SPI serial interface capable of operating with input data clock frequencies up to 50MHz. The DAC9881 requires an external reference voltage to set the output range of the DAC channel. A programmable power-on reset circuit is also incorporated into the device to ensure that the DAC output powers up at zero-scale or midscale, and in the power-down mode the output can be turned off.

CD54HC157, CD54HCT157, CD54HC158, CD54HCT158 are quad 2-input multiplexers which select four bits of data from two sources under the control of a common Select input (S).

SN65HVD50-SN65HVD55 SN65HVD56-SN65HVD59 are TI's RS-485 drivers and receivers with 1/8 unit load option supporting up to 256 nodes on the bus. This product has 15 kV HBM bus pin ESD protection, optional driver output transition time, low current standby mode (< 1 μA), glitch-free power-up and power-down bus I/Os, bus idle, open, and short circuit failsafe protection, meets or exceeds the requirements of ANSI TIA/EIA-485-A and RS-422 compatible standards.

SN54ABT853, SN74ABT853 are 8-bit to 9-bit parity bus transceivers with high reliability, low power consumption, ESD protection, and high-drive outputs.

SN54AHCT16541 and SN74AHCT16541 are 16-bit buffers/drivers with 3-state outputs. They are fabricated using the EPIC (Enhanced-Performance Implanted CMOS) process, and the inputs are TTL-voltage compatible. Distributed VCC and GND pins minimize high-speed switching noise, and the flow-through architecture optimizes PCB layout. The latch-up performance exceeds 250 mA per JESD 17. Package options include plastic shrink small-outline (DL), thin shrink small-outline (DGG), and thin very small-outline (DGV) packages, as well as a 380-mil fine-pitch ceramic flat (WD) package with 25-mil center-to-center spacings. The devices consist of two 8-bit sections with separate output-enable signals. The outputs of each section are active only when both output-enable inputs are low. If either output-enable input is high, the outputs of that section are in the high-impedance state. To ensure the high-impedance state during power up or power down, the output-enable signals should be tied to VCC through pullup resistors, with the minimum value determined by the current-sinking capability of the driver. The SN54AHCT16541 is characterized for operation over the full military temperature range of -55°C to 125°C, while the SN74AHCT16541 is characterized for operation from -40°C to 85°C.

SN74ALVCH162244 is a 16-bit buffer/driver in the Texas Instruments Widebus family. It uses the Enhanced Performance Implanted CMOS (EPIC) submicron process, and the output ports have equivalent 26-ohm series resistors, so no external resistors are required.

The SN74BCT2423A, SN74BCT2424A is a 16-bit latched multiplexer/demultiplexer bus transceiver with the following features: Multiplexed real-time and latched data, Byte control for byte-write applications, Useful in NuBus interface applications, Useful in Memory Interleave Applications, BiCMOS design substantially reduces standby current, Dependable Texas Instruments Quality and Reliability.

This data sheet provides detailed information about the SN74GTLPH1612 18-BIT LVTTL-TO-GTL+ ADJUSTABLE-EDGE-RATE UNIVERSAL BUS TRANSCEIVER, including features, pins, package, and applications.

This document is the datasheet for TI's TPS2145 and TPS2147 products. It introduces the characteristics of the two products, including the application scenarios, working principles, electrical characteristics, etc.