TEXAS Manuals

This file is a TI's LM2904, LM324 and LM358 operational amplifier introduction manual, which mainly introduces the characteristics, features, working principles and application scenarios of operational amplifiers.

This document mainly introduces the characteristics of LPV321/358/324 low-power operational amplifiers, including operating voltage range, output swing, input common-mode range, bandwidth, power consumption, etc.

bq29410, bq29411, bq29412 are second-level lithium-ion battery overvoltage protection ICs with fixed high accuracy overvoltage protection, programmable delay time of detection, high power supply ripple rejection, stable during pulse charge operation and other characteristics.

The CDC2516 is a 3.3V phase-lock loop clock driver for synchronous DRAM applications. It distributes one clock input to four banks of four outputs, with separate output enable for each output bank. The external feedback pin (FBIN) is used to synchronize the outputs to the clock input. The CDC2516 has integrated series-damping resistors on-chip and does not require an external RC network. It operates at 3.3V VCC and is packaged in a plastic 48-pin thin shrink small-outline package.

This document describes a 20-bit bus interface flip-flop with 3-state outputs, designed for driving highly-capacitive or relatively low-impedance loads. They are particularly suitable for implementing wider buffer registers, I/O ports, bidirectional bus drivers with parity, and working registers. These devices can be used as two 10-bit flip-flops or one 20-bit flip-flop.

The CY74FCT163952 and CY74FCT163H952 are low-power, pin-compatible replacements for the LCX and LPT families, with 5V-tolerant inputs and outputs, 24 mA balanced-drive outputs, power-off disable outputs that permit live insertion, edge-rate control circuitry for reduced noise, FCT-C speed at 4.4 ns, latch-up performance that exceeds JEDEC Standard No. 17, typical output skew less than 250 ps, industrial temperature range of -40˚C to +85˚C, TSSOP (19.6-mil pitch) or SSOP (25-mil pitch), typical Volp (ground bounce) performance that exceeds Mil Std 883D, VCC = 2.7V to 3.6V, ESD (HBM) > 2000V, bus hold on data inputs, eliminates the need for external pull-up or pull-down resistors, devices with bus hold are not recommended for translating rail-to-rail CMOS signals to 3.3V logic levels

ADS1274/ADS1278 is a 24-bit, delta-sigma (ΔΣ) analog-to-digital converter (ADC) from Texas Instruments that supports data rates up to 128ksps and simultaneous sampling of four/eight channels. The devices in this series use a new digital filter design that provides 62kHz bandwidth and 111dB SNR (High-Resolution Mode), making them well-suited for high-precision, high-bandwidth measurement applications.

The TS2PCIE2212 is a PCI Express™ signal switch produced by Texas Instruments that can implement 1:2 multiplexing/demultiplexing of two pairs of PCI Express™ channels and supports a data rate of 2.5 Gbps.

This document describes the features and characteristics of XIO3130, including power-up/power-down sequencing, Express interface, GPIO terminals, serial EEPROM, switch reset features, etc.

This document introduces the TPS6040x family of products, which are devices that generate an unregulated negative output voltage from an input voltage ranging from 1.6V to 5.5V. The series features a wide input voltage range, only three small 1μF ceramic capacitors required, and a maximum output current of 60mA.

This document introduces the PT5020 series of integrated switching regulators (ISRs), which convert a positive input voltage to a negative output voltage for a wide range of analog and datacom applications. These Plus to Minus ISRs incorporate a “Buck-Boost” topology and are packaged in the 3-pin, single in-line pin (SIP) package configuration.

The PT7600 is a high-performance 10 Amp Integrated Switching Regulator (ISR) designed for easy integration of high-speed low-voltage microprocessors and bus drivers into existing 5V systems. It features high efficiency, wide input voltage range, and differential remote sense. It requires 1200µF of output capacitance.

This document describes the features and characteristics of the PTH05020W series non-isolated power modules, including up to 22A output current, 5V input voltage, wide-output voltage adjust (0.8V to 3.6V), efficiencies up to 96%, 155W/in³ power density, etc.