ON Manuals (Industrial)

This is a document about 3 Watt Plastic Surface Mount Zener Voltage Regulators, which describes the features and characteristics of the product.

File format: PDF Size:73 KB

The MC74HC273A/D is an Onsemi high-performance silicon-gate CMOS octal D flip-flop with common clock and reset. Its pinout is identical to that of the LS273. The device inputs are compatible with standard CMOS outputs; with pullup resistors, they are compatible with LSTTL outputs. This device consists of eight D flip-flops with common Clock and Reset inputs. Each flip-flop is loaded with a low-to-high transition of the Clock input. Reset is asynchronous and active low.

File format: PDF Size:133 KB

The MC10EP/100EP52 is a differential data, differential clock D flip-flop. The device is pin and functionally equivalent to the EL52 device. Data enters the master portion of the flip-flop when the clock is LOW and is transferred to the slave, and thus the outputs, upon a positive transition of the clock. The differential clock inputs of the EP52 allow the device to also be used as a negative edge triggered device. The EP52 employs input clamping circuitry so that under open input conditions (pulled down to VEE) the outputs of the device will remain stable. The 100 Series contains temperature compensation. Features: 330 ps Typical Propagation Delay, Maximum Frequency - 4 GHz Typical, PECL Mode: VCC = 3.0 V to 5.5 V with VEE = 0 V, NECL Mode: VCC = 0 V with VEE = -3.0 V to -5.5 V, Open Input Default State, Safety Clamp on Inputs, Q Output Will Default LOW with Inputs Open or at VEE, Pb-Free Packages are Available.

File format: PDF Size:153 KB

The MC10/100EP35 is a higher speed/low voltage version of the EL35 JK flip−flop. The J/K data enters the master portion of the flip−flop when the clock is LOW and is transferred to the slave, and thus the outputs, upon a positive transition of the clock. The reset pin is asynchronous and is activated with a logic HIGH. The 100 Series contains temperature compensation.

File format: PDF Size:138 KB

MC74AC74/74ACT74 is a dual D-type flip-flop with Asynchronous Clear and Set inputs and complementary (Q,Q) outputs

File format: PDF Size:158 KB

File format: PDF Size:0 KB

The MC14001B series is a CMOS gate circuit constructed with P and N channel enhancement mode devices. Its primary use is in applications where low power dissipation and/or high noise immunity is desired. The supply voltage range is 3.0 Vdc to 18 Vdc, and all outputs are buffered. It is capable of driving two low-power TTL loads or one low-power Schottky TTL load over the rated temperature range. The inputs have double diode protection, except for MC14011B and MC14081B which have triple diode protection.

File format: PDF Size:131 KB

File format: PDF Size:0 KB

This datasheet introduces the features and characteristics of MC34151/MC33151 high-speed dual MOSFET drivers, including low input current, CMOS and LSTTL compatible inputs, output rise and fall times, low standby current, and high-frequency operation.

File format: PDF Size:175 KB

The MC78M00 Series positive voltage regulators are identical to the popular MC7800 Series devices, except that they are specified for only half the output current. Internal current limiting, thermal shutdown circuitry and safe−area compensation for the internal pass transistor combine to make these devices remarkably rugged under most operating conditions.

File format: PDF Size:151 KB

This document describes the features of the product designed for use in industrial-military power amplifier and switching circuit applications. It has high collector-emitter sustaining voltage, high DC current gain, low collector-emitter saturation voltage, and fast switching times.

File format: PDF Size:77 KB

This is an 8-channel EMI filter with integrated ESD protection. Typical component values of R = 28 Ω, C = 17 pF and L = 1.0 nH deliver a cutoff frequency of 125 MHz and stop band attenuation greater than −25 dB from 800 MHz to 3.0 GHz. This performance makes the part ideal for parallel interfaces with data rates up to 83 Mbps in applications where wireless interference must be minimized. The specified attenuation range is very effective in minimizing interference from 2G/3G, GPS, Bluetooth® and WLAN signals.

File format: PDF Size:186 KB

MC14099B is an 8-bit addressable latch with serial data input and parallel output functions. It can enter data in serial form when the appropriate latch is addressed (via address pins A0, A1, A2) and write disable is in the low state. The data is presented in parallel at the output of the eight latches independently of the state of Write Disable, Write/Read or Chip Enable. A Master Reset capability is available on both parts.

File format: PDF Size:102 KB

The MC10H211 is a dual 3 input 3 output NOR gate, which can drive up to 6 transmission lines simultaneously. It can also wire OR several levels of gating for minimization of gate and package count. The ability to control three parallel lines with minimum propagation delay from a single point makes the MC10H211 particularly useful in clock distribution applications where minimum clock skew is desired.

File format: PDF Size:129 KB

MC10103 is a quad 2-input OR gate with OR/NOR outputs. It features low power consumption and short propagation delay.

File format: PDF Size:108 KB

The BZX84C2V4ET1 series Zener voltage regulators are 225mW power, SOT-23 surface mount devices. These devices are designed to provide voltage regulation with minimum space requirements. They are well suited for applications such as cellular phones, hand held portables, and high density PC boards.

File format: PDF Size:85 KB

1500 Watt Peak Power Mosorb® Zener Transient Voltage Suppressors Unidirectional*

File format: PDF Size:74 KB

The MC14049UB hex inverter/buffer is constructed with MOS P–channel and N–channel enhancement mode devices in a single monolithic structure. This complementary MOS device finds primary use where low power dissipation and/or high noise immunity is desired. This device provides logic–level conversion using only one supply voltage, VDD. The input–signal high level (VIH) can exceed the VDD supply voltage for logic–level conversions. Two TTL/DTL Loads can be driven when the device is used as CMOS–to–TTL/DTL converters (VDD = 5.0 V, VOL ≤ 0.4 V, IOL ≥ 3.2 mA). Note that pins 13 and 16 are not connected internally on this device; consequently connections to these terminals will not affect circuit operation.

File format: PDF Size:208 KB

This product is MBR120ESFT1/D Surface Mount Schottky Power Rectifier Plastic SOD-123 Package, using the Schottky Barrier principle, suitable for low voltage, high frequency rectification or as free wheeling and polarity protection diodes for surface mount applications where compact size and weight are critical to the system. This package also provides an easy to work with alternative to leadless 34 package style. Because of its small size, it is ideal for use in portable and battery powered products such as cellular and cordless phones, chargers, notebook computers, printers, PDAs and PCMCIA cards.

File format: PDF Size:62 KB

The NCS2002, NCV2002 is a small, single-channel, low voltage, low power, low noise, low input bias current operational amplifier.

File format: PDF Size:202 KB