ON Manuals (Industrial)

MCR8/D is a reverse blocking thyristor designed primarily for half-wave ac control applications, such as motor controls, heating controls, and power supplies; or wherever half–wave, silicon gate–controlled devices are needed.

File format: PDF Size:96 KB

MC1489/D is a four-line EIA−232D receiver produced by ON Semiconductor. It has an input resistance of 3.0 k to 7.0 k�, an input signal range of ±30 V, an input threshold hysteresis characteristic, and can perform logic threshold shifting and input noise filtering

File format: PDF Size:99 KB

The MC100EP016A is a high-speed synchronous, presettable, cascadeable 8-bit binary counter produced by Semiconductor Components Industries, LLC, with a working frequency of up to 1.3 GHz, 30% higher than MC100EP016

File format: PDF Size:109 KB

SMA package surface mount Schottky diode, ideal for low voltage, high frequency rectification, or as free wheeling and polarity diodes in surface mount applications where compact size and weight are critical to the system.

File format: PDF Size:73 KB

2N5060 series Sensitive Gate Silicon Controlled Rectifiers Reverse Blocking Thyristors are Annular PNPN devices designed for high volume consumer applications such as relay and lamp drivers, small motor controls, gate drivers for larger thyristors, and sensing and detection circuits.

File format: PDF Size:71 KB

The NCP803 is a low power system supervisor circuit designed to monitor VCC in digital systems and provide a reset signal to the host processor when necessary. No external components are required. The reset output is driven active within 10µsec of VCC falling through the reset voltage threshold. Reset is maintained active for a minimum of 140msec after VCC rises above the reset threshold. The NCP803 has an open drain active-low RESET output. The output of the NCP803 is guaranteed valid down to VCC = 1.0V and is available in a SOT-23 package. The NCP803 is optimized to reject fast transient glitches on the VCC line. Low supply current of 1.0µA (VCC = 3.2V) make this device suitable for battery powered applications.

File format: PDF Size:58 KB

This document introduces the features of MKP3V120/D bidirectional triggers, including maximum ratings, applications, and marking.

File format: PDF Size:88 KB

This is a 24 and 40 watt peak power Zener transient voltage suppressor for ESD protection, using SOT-23 dual common anode Zener design to protect two separate lines using only one package

File format: PDF Size:71 KB

The document describes a 10-pin flip chip with a 4:1 seating plane. The dimensions and tolerances comply with ASME Y14.5M standard. The product has specific dimensions and marking information.

File format: PDF Size:26 KB

The NCV4279B is a 5.0 V precision micropower voltage regulator with an output current capability of 150 mA. The output voltage is accurate within ±2.0% with a maximum dropout voltage of 0.6 V at 150 mA. It features low quiescent current, drawing only 90 μA with a 100 μA load. This part is ideal for battery operated microprocessor equipment. The microprocessor control logic includes an active RESET (with DELAY) and a FLAG monitor, which provides an early warning signal to the microprocessor of a potential impending RESET signal. The use of the FLAG monitor allows the microprocessor to finish any signal processing before the RESET shuts it down. The active RESET circuit operates correctly at an output voltage as low as 1.0 V. The RESET function is activated during the power up sequence or if the output voltage drops outside the regulation limits during normal operation. The reset threshold voltage can be adjusted by connecting an external resistor divider to the RADJ lead. The regulator is protected against reverse battery, short circuit, and thermal overload conditions. It is suitable for use in automotive environments, as it can withstand load dump transients. The device has also been optimized for EMC conditions.

File format: PDF Size:106 KB

1SMA5913BT3 is a 1.5 watt plastic surface mount zener voltage regulator.

File format: PDF Size:83 KB

This datasheet lists in detail the maximum ratings, thermal characteristics, device marking and resistor values of DTC114E/D digital transistors.

File format: PDF Size:155 KB

NUP4103FC is an integrated transient voltage suppressor device (TVS) designed for applications requiring transient overvoltage protection. It is intended for use in sensitive portable equipment and other applications. Its integrated design provides very effective and reliable protection for four separate lines using only one package. These devices are ideal for situations where board space is a premium.

File format: PDF Size:60 KB

The NCV8504 is a family of precision micropower voltage regulators with an output current capability of 400mA. The family offers options for adjustable, 2.5V, 3.3V, and 5.0V output voltages. The output voltage is accurate within ±2.0% and has a maximum dropout voltage of 0.6V at 400mA. It features low quiescent current of only 100µA with a 100µA load, making it ideal for battery-operated microprocessor equipment. The microprocessor control logic includes an active RESET circuit with a delay. The RESET function operates correctly even at an output voltage as low as 1.0V. The reset threshold voltage can be decreased by connecting an external resistor divider to the RADJ lead. The general use comparator (FLAG/Monitor) is referenced to a temperature stable voltage and provides 1mA of drive current at its open collector output. The regulator is protected against reverse battery, short circuit, and thermal overload conditions. It can withstand load dump transients, making it suitable for automotive environments. The device has also been optimized for EMC conditions.

File format: PDF Size:111 KB

The NCP1397 is a high performance controller that can be utilized in half bridge resonant topologies such as series resonant, parallel resonant and LLC resonant converters. It integrates 600 V gate drivers, simplifying layout and reducing external component count. With its unique architecture, including a 500 kHz Voltage Controlled Oscillator whose control mode permits flexibility when an ORing function is required, the NCP1397 delivers everything needed to build a reliable and rugged resonant mode power supply.

File format: PDF Size:750 KB

MSB710-RT1 is a PNP general purpose amplifier produced by Semiconductor Components Industries, LLC. The maximum collector-emitter breakdown voltage is -50V, the maximum collector-base breakdown voltage is -60V, the maximum emitter-base breakdown voltage is -7.0V, the maximum collector current is -500mA, and the maximum peak collector current is -1.0A.

File format: PDF Size:37 KB

MC33340/D MC33340, MC33342 Battery Fast Charge Controllers are monolithic control IC's that are specifically designed as fast charge controllers for Nickel Cadmium (NiCd) and Nickel Metal Hydride (NiMH) batteries.

File format: PDF Size:203 KB

NCP3065 is a high-brightness LED constant current driver with 235mV low feedback voltage, wide input voltage range, and can be configured as step-down and step-up switching power supplies

File format: PDF Size:249 KB

MC33340 and MC33342 are monolithic control ICs specifically designed for fast charge control of Nickel Cadmium (NiCd) and Nickel Metal Hydride (NiMH) batteries. These devices use negative slope voltage detection as the primary method for fast charge termination. Accurate detection is ensured by momentarily interrupting the charge current for precise voltage sampling. An additional secondary termination method can be selected, either programmable time or temperature limit. Protective features include battery over and undervoltage detection, latched over temperature detection, and power supply input undervoltage lockout with hysteresis. The only difference between MC33340 and MC33342 is the fast charge holdoff time, with MC33340 having a typical holdoff time of 177 seconds and MC33342 having a typical holdoff time of 708 seconds.

File format: PDF Size:203 KB

The NCP300 and NCP301 series are second generation ultra-low current voltage detectors. These devices are specifically designed for use as reset controllers in portable microprocessor based systems where extended battery life is paramount. Each series features a highly accurate undervoltage detector with hysteresis which prevents erratic system reset operation as the comparator threshold is crossed. The NCP300 series consists of complementary output devices that are available with either an active high or active low reset output. The NCP301 series has an open drain N-Channel output with either an active high or active low reset output. The NCP300 and NCP301 device series are available in the Thin TSOP-5 package with standard undervoltage thresholds. Additional thresholds that range from 0.9 V to 4.9 V in 100 mV steps can be manufactured.

File format: PDF Size:173 KB