BD Cytometric Bead Array Human Active Caspase-3 CBA Kit Manual

BD CBA Human Active Caspase-3 kit (Cat. No. 552124) instructions for measuring active caspase-3 protein in cell lysates by flow cytometry.


BD Cytometric Bead Array Human Active Caspase-3 CBA Kit Manual - cover page
Brand
B&D
Category
Health Care
Document type
User Manual
Language
English
Pages
28
File format
PDF
File size
404 KB
Published
08 November, 2026
Updated
08 November, 2026
MD5 checksum
11A495652BC7D634707FD3CD8E9F4BAE

About this manual

This manual describes the BD Cytometric Bead Array (CBA) Human Active Caspase-3 kit, Cat. No. 552124. The kit uses a single bead population coated with a capture antibody specific for caspase-3, a PE-conjugated detection antibody, and a lyophilized cell lysate standard to form sandwich complexes that are read on a flow cytometer and analyzed with BD CBA Software. The kit provides reagents for the quantitative analysis of 100 samples, including up to three standard curve sets, and is intended for research use only.

The document covers the principle of the test, reagents provided and materials required but not provided, preparation of the lysate standard, cell lysis buffer mixture and test samples, the assay procedure, cytometer setup with BD FACSComp software and Cytometer Setup Beads, data acquisition and analysis, typical data, performance (sensitivity, specificity, precision), and troubleshooting tips. Storage instructions and hazardous ingredient information for the kit components are also given.

What's inside

  • Introduction
  • Principle of the Test
  • Advantages
  • Limitations
  • Reagents Provided
  • Materials Required but not Provided
  • Overview: Human Active Caspase-3 CBA Assay Procedure
  • Preparation of Human Active Caspase-3 Lysate Standard
  • Preparation of Cell Lysis Buffer Mixture
  • Preparation of Test Samples

Specifications

Storage temperature of kit components4 °C
Human Caspase-3 Capture Beads1 vial, 5 ml (100-test vial)
Human Active Caspase-3 PE Detection Reagent1 vial, 5 ml; 50 µl/test
Human Active Caspase-3 Lysate Standard3 vials, 0.2 ml lyophilized; 30,000 Units/ml after reconstitution
Cytometer Setup Beads1 vial, 1.5 ml; 30 tests, sufficient for 10 setup procedures
Wash Buffer1 bottle, 130 ml (PBS solution, 1×)
Assay Diluent1 bottle, 30 ml (1×)
Number of samples supported100 samples
Required flow cytometer488 nm laser, detecting emissions at 576 and 670 nm
Protease Inhibitor Cocktail1 vial, 1 ml lyophilized; reconstituted to 50× bulk

Frequently asked questions

What is the BD Human Active Caspase-3 CBA kit used for?

It is used to quantitatively measure active caspase-3 protein levels in a single cell lysate sample, using flow cytometry.

How many samples can be analyzed with one kit?

The kit provides sufficient reagents for quantitative analysis of 100 samples, including generation of up to three standard curve sets.

What instrument is required to run the assay?

A flow cytometer with a 488 nm laser that can detect fluorescence emissions at 576 and 670 nm, such as a BD FACScan or BD FACSCalibur instrument.

How should the capture beads be stored and handled?

Store them at 4 °C and do not freeze; vortex the vial vigorously for 3–5 seconds before taking an aliquot because the beads settle out of suspension.

How is the lysate standard reconstituted?

Each vial is reconstituted in 0.2 ml of deionized water to prepare a 5× bulk standard, which should be stored at 2–8 °C and used within 12 hours.

Download PDF (404 KB)

More B&D Manuals


View all B&D manuals →