Skyworks Si3406 Isolated Flyback EVB User Guide

This user guide introduces the Si3406 isolated Flyback evaluation board, a reference design for a power supply in a Power over Ethernet (PoE) Powered Device (PD) application. This Si3406-Flyback EVB provides simple and low-cost solution with different output voltages and power levels.


Skyworks Si3406 Isolated Flyback EVB User Guide - cover page
Brand
Skyworks
Category
demo board
Document type
User Manual
Language
English
Pages
92
File format
PDF
File size
8.4 MB
Published
16 October, 2023
Updated
16 October, 2023
MD5 checksum
B66B8F4807A889AFA369FA2B37A3A3AE

About this manual

This user guide (UG443) describes the Si3406 isolated flyback evaluation board, a reference design for a power supply in a Power over Ethernet (PoE) Powered Device application. The Si3406 IC integrates an IEEE 802.3at compatible PoE interface and a current control-based dc/dc converter, including an internal rectifier bridge, detection and classification circuits, hotswap switch, TVS overvoltage protection and thermal shutdown. The guide presents three output voltage variants: 3.3 V, 5 V and 12 V at Class 2.

The document includes a selector guide, instructions for powering up the Si3406-ISO-FB board through the RJ45 connector with a PoE-capable PSE or a laboratory power supply, and complete schematics for the 3.3 V, Class 2, 7 W configuration. End-to-end efficiency charts and thermal measurement data for the 3.3 V board are also provided, along with the recommended detection resistor values for internal, external silicon and external Schottky diode bridges.

What's inside

  • Selector Guide
  • Powering Up the Si3406-ISO-FB Board
  • Si3406-ISO-FB EVB: 3.3 V, Class 2 Configuration
  • Si3406-ISO-FB EVB Schematic: 3.3 V, Class 2, 7W
  • End-to-End EVB Efficiency
  • Thermal Measurements

Specifications

PSE input voltage range37 V to 57 V (connector J1)
PoE Type/ClassIEEE 802.3at Type 1/Class 2
Output voltage / current3.3 V / 1.5 A; 5 V / 1.05 A; 12 V / 0.45 A (connectors J2-J3)
Switching frequency177 kHz (R18 = 110 kΩ), 150 kHz (130 kΩ), 123 kHz (160 kΩ)
Maximum output powerup to 7 W, limited by the internal rectifier bridge
PackageLow-profile 4 x 4 mm 20-pin QFN
Radiated EMIEN55032 Class B - Passed
Ordering part numbersSi3406FB3V2KIT, Si3406FB5V2KIT, Si3406FB12V2KIT

Frequently asked questions

What input voltage range does the Si3406 isolated flyback EVB accept?

The PSE input voltage range at connector J1 is 37 V to 57 V.

Which output voltages does the evaluation board support?

The user guide presents three output voltages: 3.3 V, 5 V and 12 V, all in Class 2 configurations rated at 7 W.

How is power applied to the Si3406-ISO-FB board?

Ethernet data and power are applied through the RJ45 connector (U2), using any IEEE 802.3-2015-compliant PoE-capable PSE or a laboratory power supply unit connected to the Ethernet cable pairs.

How is the switching frequency set on the board?

It is set by installing R18: 110 kΩ for 177 kHz, 130 kΩ for 150 kHz and 160 kΩ for 123 kHz at the 3.3 V, 5 V and 12 V levels respectively.

Download PDF (8.4 MB)

More Skyworks Manuals


View all Skyworks manuals →