Error Codes

Error, fault and alarm codes of products - what each code means, its causes and what to do - read from the manufacturers’ manuals, with the manual page each answer comes from.

• CodeMitsubishi Electric 2033 G Series Error UF056: Converter overcurrent

  Converter overcurrent due to converter over-current condition. The manual's first action is: “CALL SERVICE ENGINEER”

• CodeMitsubishi Electric 2033 G Series Error UF003: Converter abnormal

  Converter abnormal because preliminary charge is impossible. The manual's first action is: “CALL SERVICE ENGINEER”

• Code listMitsubishi Electric 2033 G Series Error Codes

  All 48 error codes of the Mitsubishi Electric 2033 G Series UPS with their meaning, causes and what to do, taken from the manufacturer's manual with page references.

• CodeDanfoss 100 FLOW Error 1113: Pump Running Time

  Pump Running Time means a pump run-time counter has exceeded a user-specified alarm limit in a multi-pump system. The manual's first action is: “Do the necessary maintenance actions, reset the run-time counter, and re…

• CodeDanfoss 100 FLOW Error 1318: Temperature Fault 2

  Temperature Fault 2 means one or more temperature inputs set in P3.9.6.5 are above the fault limit, requiring sensor or wiring check. The manual's first action is: “Find the cause of the temperature rise.”

• CodeDanfoss 100 FLOW Error 1317: Temperature Fault 2

  Temperature Fault 2 means one or more temperature inputs set in P3.9.6.5 are above the fault limit, requiring sensor or wiring check. The manual's first action is: “Find the cause of the temperature rise.”

• CodeDanfoss 100 FLOW Error 1316: Temperature Fault 2

  Temperature Fault 2 means one or more temperature inputs set in P3.9.6.5 are above the fault limit, requiring sensor or wiring check. The manual's first action is: “Find the cause of the temperature rise.”

• CodeDanfoss 100 FLOW Error 1315: Temperature Fault 1

  Temperature Fault 1 means one or more temperature inputs are above the fault limit, requiring sensor or wiring check. The manual's first action is: “Find the cause of the temperature rise.”

• CodeDanfoss 100 FLOW Error 111: Temperature Fault 1

  Temperature Fault 1 means one or more temperature inputs are above the alarm limit, requiring sensor or wiring check. The manual's first action is: “Find the cause of the temperature rise.”

• CodeDanfoss 100 FLOW Error 1409: ID 1409 - Input Pressure Supervision

  ID 1409 - Input Pressure Supervision means the input pressure signal is below the fault limit set in P3.13.9.8. The manual lists no action for this code.

• CodeDanfoss 100 FLOW Error 109: ID 1109 - Input Pressure Supervision

  ID 1109 - Input Pressure Supervision means the input pressure signal is below the alarm limit set in P3.13.9.7. The manual's first action is: “Check the process.”

• CodeDanfoss 100 FLOW Error 105: ID 1105 - Feedback Supervision Fault (ExtPID)

  ID 1105 - Feedback Supervision Fault (ExtPID) means the feedback value is outside supervision limits or delay settings for ExtPID. The manual's first action is: “Check the process.”

• CodeDanfoss 100 FLOW Error 101: ID 1101 - Feedback Supervision Fault (PID 1)

  ID 1101 - Feedback Supervision Fault (PID 1) means the feedback value is outside supervision limits or delay settings for PID 1. The manual's first action is: “Check the process.”

• CodeDanfoss 100 FLOW Error 100: ID 1100 - Soft Fill Timeout

  ID 1100 - Soft Fill Timeout means the PID controller did not achieve the process value within its time limit, possibly due to a broken pipe. The manual's first action is: “Check the process.”

• CodeDanfoss 100 FLOW Error 78: ID 1078 - Identification Ongoing

  ID 1078 - Identification Ongoing means the drive is running identification for the motor. The manual's first action is: “You can stop the identification run at any time by removing the start command. When the identifi…