Industrial

The ADS8318 is a 16-bit, 500-ksps analog-to-digital converter from TI. It has a 50-MHz SPI compatible serial interface and supports multiple device cascading.

The LTC®3808 is a synchronous step-down switching regulator controller that drives external complementary power MOSFETs using few external components. The constant frequency current mode architecture with MOSFET VDS sensing eliminates the need for a current sense resistor and improves efficiency. By employing Spread Spectrum modulation technology, the device achieves low noise over a wide input voltage range.

This document is the SFH615A/SFH6156 optocoupler product manual from Vishay Semiconductors. It features excellent linearity, high reliability, high isolation voltage, etc.

The MICRF218 is the world's first integrated ASK / OOK receiver with selectable dual IF bandwidths for 300~450 MHz operation. It has a fully integrated IF section with image rejection, providing performance, simplicity, and ease of implementation for the receiver portion of RF actuation. The MICRF218 is a true RF in, data out receiver. It features built-in IF filter and image rejection functions. The dual IF bandwidths allow the MICRF218 to capture signals from high performance or low cost transmitters. Additionally, the MICRF218 provides post-detection data filtering with a choice of four filter bandwidths ranging from 1.25 kHz to 10 kHz. The device can be programmed with easily determined values based on data rate, code modulation format, and desired duty-cycle operation. The MICRF218 includes a shutdown control for duty-cycle operation to reduce average current consumption. It also has an analog RSSI output to indicate the strength of incoming signals. The device is unique for its ability to e...

This document is about the programming specification of PIC16C50X, including hardware requirements, programming mode, and how to enter programming mode.

The DAC128S085 is a 12-bit micro power octal digital-to-analog converter with rail-to-rail outputs, which can operate from a single +2.7V to +5.5V supply and consumes only 1.95 mW of power.

The DAC108S085 is a full-featured, general purpose OCTAL 10-bit voltage-output digital-to-analog converter (DAC) that can operate from a single +2.7V to +5.5V supply and consumes 1.95 mW at 3V and 4.85 mW at 5V. The DAC108S085 is packaged in a 16-lead LLP package and a 16-lead TSSOP package. The LLP package makes the DAC108S085 the smallest OCTAL DAC in its class. The on-chip output amplifiers allow rail-to-rail output swing and the three wire serial interface operates at clock rates up to 40 MHz over the entire supply voltage range. Competitive devices are limited to 25 MHz clock rates at supply voltages in the 2.7V to 3.6V range. The serial interface is compatible with standard SPI™, QSPI, MICROWIRE and DSP interfaces. The DAC108S085 also offers daisy chain operation where an unlimited number of DAC108S085s can be updated simultaneously using a single serial interface. There are two references for the DAC108S085. One reference input serves channels A through D while the other reference serves channels E through H. Each reference can be set independently between 0.5V and VA, providing the widest possible output dynamic range. The DAC108S085 has a 16-bit input shift register that controls the mode of operation, the power-down condition, and the DAC channels' register/output value. All eight DAC outputs can be updated simultaneously or individually.

The TFDU5307 is an infrared transceiver module compliant to the latest IrDA physical layer standard, supporting IrDA speeds up to 1.152 Mbit/s (MIR) and carrier based remote control modes up to 2 MHz. It is built in a low profile package and has a tri-state output.

The LTC1704/LTC1704B is a high power synchronous switching regulator controller with high efficiency and low power consumption, suitable for a variety of applications.

The ADS1601 is a high-performance, high-precision, high-speed, low-power analog-to-digital converter (ADC). ADS1601 is used for sonar, vibration analysis and data acquisition.

Low power RS-485 / RS-422 differential bus transceiver.

This document describes the features and characteristics of Vishay Semiconductors VLMO/S/Y30.. low current SMD LED, including exceptional brightness, compatibility with automatic placement equipment, EIA and ICE standard package, compatibility with various solder processes, excellent for coupling to light pipes and backlighting, low power consumption, high ESD withstand voltage, and compliance with RoHS and WEEE requirements.