Industrial

This file is the specification of KEMET's CERAMIC CHIP / HIGH VOLTAGE product

This document introduces the characteristics of Welwyn Components' WH series resistors, including power, resistance range, TCR, resistance range, low value limits, limiting voltage, standard values, and temperature range.

MicroLAN coupler is an essential component to build and control 1-Wire MicroLAN networks with multi-level branching. In contrast to approaches that switch the ground line, the coupler maintains a common ground level for the whole network and keeps the inactive segments powered. This simplifies supplying central or local power for added devices.

Search for Q4401I1S1 suppliers

This PDF file is the EI brand's M12 inductive sensor product manual, which introduces the features and characteristics of the product, including appearance, size, sensing distance, power supply, output type, protection functions, etc.

The LTC1154 is a high-side micropower MOSFET driver that allows using low cost N-channel FETs for high-side switching applications. It features 8µA IQ standby current, 85µA IQ ON current, no external charge pump capacitors, 4.5V to 18V supply range, short-circuit protection, thermal shutdown via PTC thermistor, status output indicates shutdown, and is available in 8-pin SOIC package.

TE100R-TE108R are TE's glass passivated junction fast switching rectifiers, rated voltage is 50 to 800 volts, rated current is 1 ampere.

LTC3421/3421f is a low-power synchronous boost converter with a maximum operating frequency of 3MHz. The input voltage range is 0.5V~4.5V, and the output voltage range is 2.4V~5.25V. It has synchronous rectification, output disconnect, inrush current limiting, low quiescent current, high efficiency, programmable current limit, programmable soft start, synchronous oscillator, manual or automatic burst mode, low battery comparator and other characteristics.

RLZ36B Diodes Rev.A is a Zener diode with a voltage regulation of 3.6V. It has a maximum power dissipation of 175mW and a storage temperature of -65 to +175℃. The diode is available in a LLDS package.

IR2177/IR2277 is a high voltage, high speed, single phase current sensor interface for AC motor drive applications. The current is sensed by an external shunt resistor. The IC converts the analog voltage into a time interval through a precise circuit that also performs a very good ripple rejection showing small group delay. The time interval is level shifted and given to the output both as a PWM signal (PO) and analog voltage (OUT). The analog voltage is proportional to the measured current and is ratio metric with respect to an externally provided voltage reference. The max throughput is 40 ksample/sec suitable for up to 20 kHz asymmetrical PWM modulation and max delay is <7.5 µsec (@20kHz). Also a fast over current signal is provided for IGBT protection.

The SL1122A series Hybrid 2 Electrode Gas Discharge Tube (GDT) features excellent response to fast rising transients, flat response up to 10kV/μs, and 10kA surge capability tested with 8/20μs pulse as defined by IEC 61000-4-5. It is suitable for MDF protection, ADSL equipment, XDSL equipment, alarm panels, and general telecom equipment.

DP83843BVJE PHYTER is a VLSI device produced by National Semiconductor Corporation that supports both 10BASE-T and 100BASE-X Ethernet protocols.

This document describes the features and applications of the ADS8327 and ADS8328, low power, 16-bit, 500kHz, single/dual unipolar input analog-to-digital converters with a serial interface.

FLEXSTRIP® JUMPERS is a flexible interconnection system from Germany Würth Elektronik, which can achieve multi-conductor board-to-board connection without stripping, cutting to length or solder preparation. It can be used as an alternative to conventional point-to-point wiring, providing a comprehensive range of board-to-board jumpers that can be repeatedly flexed without failure. Leveraging industry-leading improvements in contact reliability, low height profile, compatibility with auto insertion equipment, and ease of assembly, FLEXSTRIP® JUMPERS provides an optimal solution for a diverse range of applications that require a reliable high performance interconnect. Its performance benefits are key to the flat conductor construction achieved by a special manufacturing process. Round conductors rolled flat provide unrivalled flexibility and resistance against vibration and high flexing cycles. Conventional round pins at each end ensure simplified assembly and soldering. The smooth notchless transition from the flat conductor to the round contact pin guarantees a termination area that is break-proof and free of stress. Strong vibrations can generate frequencies that can lead to resonance in the structure of equipment and the printed circuit board. For this reason, a high degree of stress often occurs at the termination points in particular, which are typically the weakest links in the system. Such stresses are frequently responsible for damage to the contact pins. FLEXSTRIP® JUMPERS effectively prevents damage to the contact pins.