Industrial

The DS90C032B is a quad CMOS differential line receiver designed for applications requiring ultra low power dissipation and high data rates. The device is designed to support data rates in excess of 155.5 Mbps (77.7 MHz) utilizing Low Voltage Differential Signaling (LVDS) technology.

Vol-Con® Elite Voltage / Continuity Tester Instruction Sheet WARNINGS To avoid possible electric shock, personal injury, or death, follow these guidelines. • Do not use if tester appears damaged or is not operating properly. • Inspect and replace leads if insulation is damaged, metal is exposed, or probes are cracked. • Do not use meter if it operates abnormally as protection may be impaired. • Do not use tester for more than the rated voltage on the tester. • Do not use without the battery and the back case properly installed. • Do not apply more than the rated voltage to the meter. • Do not use during electrical storms or in wet weather. • Do not use around explosive gas, dust, or vapor. • Ensure all fingers are behind finger guard when testing for voltage. • This tester will not detect voltages at a distance, such as through walls, metal conduit, or shielded wire. • Before each use perform a continuity test by touching the probe tips together, an audible sound should be heard and the continuity [•)))] LED should light. This test verifies the functionality of the battery and test leads. • Use the 3 Point Safety Method. (1) Verify tester operation by measuring a known voltage. (2) Apply tester to circuit under test. (3) Return to the known live voltage again to ensure proper operation. • Replace batteries as soon as low battery indicator appears. • If this tester is used in a manner not specified by IDEAL, protection provided by the product may be impaired.

The DS90C032 is a low power, high speed, quad channel LVDS receiver from Texas Instruments.

This document is an instruction manual for a multimeter, which includes the use of the product, precautions, features and characteristics, etc.

This document introduces the use of Vol-Con® Voltage/ Continuity Tester (61-076) Vol-Test™ Voltage Tester (61-065) products, including safety information, warnings, cautions, etc.

The Volt Sensor is a portable voltage detection device that can detect voltages ranging from 40-600VAC. It provides audible and visual indications to easily recognize the presence of voltage. Safety warnings should be followed, such as not operating without the clip and not using it for detecting DC power.

The DS90C031B is a quad CMOS differential line driver designed for applications requiring ultra low power dissipation and high data rates. The device is designed to support data rates in excess of 155.5 Mbps (77.7 MHz) utilizing Low Voltage Differential Signaling (LVDS) technology. The DS90C031B accepts TTL/CMOS input levels and translates them to low voltage (350 mV) differential output signals. In addition the driver supports a TRI-STATE® function that may be used to disable the output stage, disabling the load current, and thus dropping the device to an ultra low idle power state of 11 mW typical. In addition, the DS90C031B provides power-off high impedance LVDS outputs. This feature assures minimal loading effect on the LVDS bus lines when VCC is not present. The DS90C031B and companion line receiver (DS90C032B) provide a new alternative to high power pseudo-ECL devices for high speed point-to-point interface applications.

SureTest® Arc Branch Circuit Tester Operating Instructions

The DS90C031 is a quad CMOS differential line driver designed by National Semiconductor Corporation for applications requiring ultra low power dissipation and high data rates. The device is designed to support data rates in excess of 155.5 Mbps (77.7 MHz) utilizing Low Voltage Differential Signaling (LVDS) technology. The DS90C031 accepts TTL/CMOS input levels and translates them to low voltage (350 mV) differential output signals. In addition, the driver supports a TRI-STATE® function that may be used to disable the output stage, disabling the load current, and thus dropping the device to an ultra low idle power state of 11 mW typical.

The E-Z Check® Plus G.F.C.I. Tester is a testing instrument from E-Z Check brand, which can test multiple circuit conditions, such as open ground, test for GFCI, hot on neutral and hot open, open neutral, hot and ground reversed, open hot and reverse polarity.

The DS9098P iButton Retainer is a low-cost, surface-mount device to secure an F5 iButton on a printed circuit board. It consists of three metal pieces (two for GROUND, one for DATA) molded into a body of black, heat-stabilized plastic.

The DS9098 iButton Retainer is a low-cost, surface-mount device that retains a 16.3 mm x 5.8 mm MicroCan on a printed circuit board. The slender design secures the iButton for a compact printed circuit board mount. The retainer latches the flange of the iButton and prevents reversed insertion.

This is a manual for the 480 series digital multimeter

This is an operating manual, which introduces the use of Heat Elite Pro Heat Gun.