Industrial

CS8126, -1, -2 is a 5V, 750mA low dropout linear regulator with delayed reset function. This regulator is an improved replacement for the CS8156. Improvements include higher accuracy, tighter saturation control, better supply rejection and enhanced circuitry.

The CS8122 is a precision 5V linear regulator capable of sourcing in excess of 750mA. The delay time is externally programmed using a discrete RC network. During power up, or when the output goes out of regulation, the lead remains in the low state for the duration of the delay. This function is independent of the input voltage and will function correctly as long as the output voltage remains at or above 1V. Hysteresis is included in the Delay and the comparators to improve noise immunity. A latching discharge circuit is used to discharge the delay capacitor when it is triggered by a brief fault condition. The regulator is protected against a variety of fault conditions: i.e. reverse battery, overvoltage, short circuit and thermal runaway conditions. The regu- lator is protected against voltage tran- sients ranging from -50V to +40V. Short circuit current is limited to 1.2A (typ). The CS8122 is an improved replacement for the CS8126 and features a tighter tol- erance on its output voltage (2% vs 4%). The CS8122 is packaged in a 5 lead TOÐ220 with copper tab. The copper tab can be connected to a heat sink if necessary.

The CS8121 is a 5V, 1A precision linear regulator with two microprocessor compatible control functions and protection circuitry included on chip. The composite NPN-PNP output pass transistor assures a lower dropout voltage (1.2V @ 1A) without requiring excessive supply current (4mA). The CS8121Õs two logic control functions make this regulator well suited to applications requiring microprocessor- based control at the board or module level. controls the output stage. A high voltage (>2.9V) on the lead turns off the regulatorÕs pass transistor and sends the IC into Sleep mode where it draws only 250µA. sends a signal when the IC is powering up or whenever the output voltage falls out of regulation. The signal is valid down to VOUT = 1V. The CS8121 design optimizes supply rejection by switching the internal bandgap reference from the supply input to the regulator output as soon as the nominal output voltage is achieved. Additional on chip filtering enhances rejection of high frequency transients on all external leads. The CS8121 is fault protected against short circuit, over voltage and thermal runaway conditions.

The CS8120 is a 5V, 300mA precision linear regulator with two microprocessor compatible control functions and protection circuitry included on chip. It features over voltage shutdown, RESET comparator, error amplifier, enable comparator, bandgap supply, output current limit, bandgap reference, thermal shutdown, load dump, and more.

The CS8101 is a precision 5V micropower voltage regulator with very low quiescent current (70µA typ at 100µA load). The 5V output is accurate within ±2% and supplies 100mA of load current with a typical dropout voltage of only 400mV. Microprocessor control logic includes an input and an active circuit. This combination of low quiescent current, outstanding regulator performance and control logic makes the CS8101 ideal for any battery operated, microprocessor controlled equipment. The active circuit includes hysteresis, and operates correctly at an output voltage as low as 1V. The function is activated during the power up sequence or during normal operation if the output voltage drops outside the regulation limits by more than 200mV typ. The logic level compatible input allows the user to put the regulator into a shutdown mode where it draws only 20µA typical of quiescent current. The regulator is protected against reverse battery, short circuit, over voltage, and thermal overload conditions. The device can withstand load dump transients making it suitable for use in automotive environments. The CS8101 is functionally equivalent to the National Semiconductor LP2951 series low current regulators.

The CS81 series is a highly integrated CMOS ASIC chip with high speed and low power consumption. This series uses 0.18µm CMOS technology and can integrate up to 40 million gates, with a gate delay time of 11ps, resulting in three times higher integration and speed compared to conventional products. In addition, this series can operate at a power-supply voltage of up to 1.1V, significantly reducing power consumption.

80C88 is a high performance 8/16-bit CMOS CPU manufactured using a self-aligned silicon gate CMOS process (Scaled SAJI IV). Two modes of operation, MINimum for small systems and MAXimum for larger applications such as multiprocessing, allow user configuration to achieve the highest performance level.

This document describes the features and characteristics of the Intersil 80C86 CMOS 16-bit microprocessor, including compatibility with NMOS 8086, completely static CMOS design, low power operation, 1MB direct memory addressing capability, various addressing modes, and arithmetic operations.

This document introduces a high-performance microprocessor called 80C286 with memory management and protection features. It is compatible with NMOS 80286 and has a wide range of clock rates and low power operation. The processor has a large address space, integrated memory management, four-level memory protection, and support for virtual memory and operating systems. It also has two operating modes, compatibility with 80287 numeric data co-processor, and a high-bandwidth bus interface.

This document describes the technical data and features of the 1-385 H High Bandwidth, Analog/Video Optocouplers. The product features wide bandwidth, high voltage gain, low GV temperature coefficient, high linearity at low drive currents, and high-speed AlGaAs emitter. It is suitable for video isolation for various standards/formats, low drive current feedback element in switching power supplies, A/D converter signal isolation, analog signal ground isolation, and high voltage insulation applications.

This data sheet describes the performance of 1-49H Intelligent Power Module and Gate Drive Interface Optocouplers

The ISSI IS41LV8200A is a 2,097,152 x 8-bit high-performance CMOS Dynamic Random Access Memory with Extended Data-Out (EDO) Page Mode access cycle. These devices offer TTL compatible inputs and outputs, a refresh interval of 2,048 cycles/32 ms, and refresh modes including RAS-Only, CAS-before-RAS (CBR), and Hidden. It operates on a single power supply of 3.3V ± 10% and supports byte write and byte read operations via two CAS signals. The IS41LV8200A is suitable for high-bandwidth graphics, digital signal processing, high-performance computing systems, and peripheral applications.

This document is the datasheet of HCPL-4504, HCPL-0454, HCNW4504. It mainly introduces the features of the product, such as short propagation delay, high common mode transient immunity, high CTR, TTL compatibility, safety approval, application scenarios, etc.

This white paper introduces Intel® Data Science Suite 4.0, the latest version of the suite that provides data scientists with more powerful and flexible capabilities for production environments. The suite includes a range of tools and libraries to help data scientists improve productivity throughout the data science lifecycle. These tools include tools for data preparation, machine learning modeling, model deployment, and model management. Intel® Data Science Suite 4.0 also includes new features such as automated machine learning, enhanced model explainability and visualization, data management and governance capabilities, and support for containers and Kubernetes.

HCPL-22XX series is a high voltage, wide voltage range of optocouplers, which can isolate electrical signals and high voltages and have high common mode rejection ratio, low input current and low propagation delay.