Maxim manuals, page 102
MAXIM MAX1978/MAX1979 Manual
The MAX1978/MAX1979 are the smallest, safest, most accurate complete single-chip temperature controllers for Peltier thermoelectric cooler (TEC) modules.
MAXIM INTEGRATED DS2780 Standalone Fuel Gauge IC Manual
This document introduces the characteristics of DS2780 product, including voltage, temperature, current measurement, and available capacity estimation. The product is suitable for rechargeable lithium ion and lithium ion polymer batteries.
MAXIM MAX3222/MAX3232/MAX3237/MAX3241*handbook
the max3222/max3232/max3237/max3241 is a serial port transceiver that supports 120kbps, 250kbps and 1mbps data transfer rates, supporting the rs-232 protocol.
MAXIM DS2715 NiMH Battery Pack Charge Controller handbook
This file introduces the function and characteristics of the DS2715 NiMH battery pack charge controller, including: charging 1 to 10 NiMH cells in series, charging current regulation, charge mode selection, and charge end conditions
MAXIM INTEGRATED PRODUCTS MAX3222/MAX3232/MAX3237/MAX3241* 3.0V to 5.5V Low-Power up to 1Mbps True RS-232 Transceivers Using Four 0.1 F External Capacitors handbook
The MAX3222/MAX3232/MAX3237/MAX3241 are 4-wire serial communication chips with a proprietary low-dropout transmitter output stage that supports the RS-232 standard protocol and can operate at a supply voltage of 3.0V to 5.5V.
MAXIM MAX3311E/MAX3313E Transceivers handbook
The MAX3311E/MAX3313E are low-power, 5V EIA/TIA-232-compatible transceivers. All transmitter outputs and receiver inputs are protected to ±15kV using the Human Body Model, making these devices ideal for applications where more robust transceivers are required. Both devices have one transmitter and one receiver. The transmitters have a proprietary low-dropout trans- mitter output stage enabling RS-232-compatible opera- tion from a +5V supply with a single inverting charge pump. These transceivers require only three 0.1µF capacitors and will run at data rates up to 460kbps while maintaining RS-232-compatible output levels. The MAX3311E features a 1µA shutdown mode. In shutdown the device turns off the charge pump, pulls V- to ground, and the transmitter output is disabled. The MAX3313E features an INVALID output that asserts high when an active RS-232 cable signal is connected, signaling to the host that a peripheral is connected to the communication port.
MAXIM MAX1196 Manual
The MAX1196 is a 3V, dual 8-bit analog-to-digital con- verter (ADC) featuring fully differential wideband track- and-hold (T/H) inputs, driving two ADCs. The MAX1196 is optimized for low power, small size, and high-dynamic performance for applications in imaging, instrumenta- tion, and digital communications. This ADC operates from a single 2.7V to 3.6V supply, consuming only 87mW while delivering a typical signal-to-noise and dis- tortion (SINAD) of 48.4dB at an input frequency of 20MHz and a sampling rate of 40Msps. The T/H driven input stages incorporate 400MHz (-3dB) input ampli- fiers. The converters can also be operated with single- ended inputs. In addition to low operating power, the MAX1196 features a 3mA sleep mode as well as a 0.1µA power-down mode to conserve power during idle periods. An internal 2.048V precision bandgap reference sets the full-scale range of the ADC. A flexible reference structure allows the use of this internal or an externally applied reference, if desired for applications requiring increased accuracy or a different input voltage range. The MAX1196 features parallel, multiplexed, CMOS- compatible three-state outputs. The digital output format can be set to two’s complement or straight offset binary through a single control pin. The device provides for a separate output power supply of 1.7V to 3.6V for flexible interfacing. The MAX1196 is available in a 7mm × 7mm, 48-pin TQFP package, and is specified for the extended indust
MAXIM MAX3380E/MAX3381E Manual
The MAX3380E/MAX3381E are +2.35V to +5.5V-powered EIA/TIA-232 and V.28/V.24 communication interfaces with low power requirements, high data-rate capabilities, and enhanced electrostatic discharge (ESD) protection on both the TTL and RS-232 sides.
MAXIM 2MHz High-Brightness LED Drivers with Integrated MOSFET High-Side Current Sense MAX16832A/MAX16832C Manual
The MAX16832A/MAX16832C step-down constant-current high-brightness LED (HB LED) drivers provide a cost-effective design solution for automotive interior/exterior lighting, architectural and ambient lighting, LED bulbs, and other LED illumination applications. The MAX16832A/MAX16832C operate from a +6.5V to +65V input voltage range. A high-side current-sense resistor adjusts the output current up to 700mA, and a dedicated pulse-width modulation (PWM) input enables pulsed LED dimming over a wide range of brightness levels. These devices are well suited for applications requiring a wide input voltage range. The high-side current sensing and an integrated current-setting circuitry minimize the number of external components while delivering an average output current with ±3% accuracy. A hysteretic control method ensures excellent input supply rejection and fast response during load transients and PWM dimming. The MAX16832A allows 10% current ripple, and the MAX16832C allows 30% current ripple. Both devices operate up to a 2MHz switching frequency, thus allowing the use of small-sized components. The MAX16832A/MAX16832C offer an analog dimming feature that reduces the output current by applying an external DC voltage below the internal 2V threshold voltage from TEMP_I to GND. TEMP_I also sources 25µA to a negative temperature coefficient (NTC) thermistor connected between TEMP_I and GND, thus providing an analog thermal-foldback feature that reduces the output current when the current reaches the rated value.
MAXIM MAX8790A INTEGRATED PRODUCTS Six-String White LED Driver with Active Current Balancing for LCD Panel Applications handbook
MAXIM DS2711 DS2712 DATA SHEET
DS2711/DS2712 is a 2-cell NiMH battery charger, which supports NiCd batteries
MAXIM MAX16822A/MAX16822B Manual
The MAX16822A/MAX16822B step-down constant-current high-brightness LED (HB LED) drivers provide a cost-effective design solution for automotive interior/exterior lighting, architectural and ambient lighting, LED bulbs, and other LED illumination applications. They operate from a wide input-voltage range and support pulsed LED dimming and constant current control. They have excellent input supply rejection and fast response capability, supporting PWM dimming and negative temperature coefficient thermal-foldback feature.
MAXIM MAX8662/MAX8663 User Manual
MAX8662/MAX8663 is a power management IC produced by Maxim for single-cell lithium-ion battery-powered devices. It is efficient and compact, and is suitable for smart phones, PDAs, Internet devices and other portable devices.
MAXIM INTEGRATED MAX1186 Manual
The MAX1186 is a 3V, dual 10-bit analog-to-digital converter (ADC) featuring fully-differential wideband track-and-hold (T/H) inputs, driving two pipelined, nine-stage ADCs. The MAX1186 is optimized for low-power, high dynamic performance applications in imaging, instrumentation, and digital communication applications. This ADC operates from a single 2.7V to 3.6V supply, consuming only 105mW while delivering a typical signal-to-noise ratio (SNR) of 59.4dB at an input frequency of 20MHz and a sampling rate of 40Msps. Digital outputs A and B are updated alternating on the rising (CHA) and the falling (CHB) edge of the clock. The T/H driven input stages incorporate 400MHz (-3dB) input amplifiers. The converters may also be operated with single-ended inputs. In addition to low operating power, the MAX1186 features a 2.8mA sleep mode as well as a 1µA power-down mode to conserve power during idle periods. An internal 2.048V precision bandgap reference sets the full-scale range of the ADCs. A flexible reference structure allows the use of this internal or an externally derived reference, if desired for applications requiring increased accuracy or a different input voltage range. The MAX1186 features parallel, multiplexed, CMOS-compatible three-state outputs. The digital output format can be set to two’s complement or straight offset binary through a single control pin. The device provides for a separate output power supply of 1.7V to 3.6V for flexibility.
MAXIM MAX3221E/MAX3223E/MAX3243E User's manual
The MAX3221E/MAX3223E/MAX3243E are 3V-powered EIA/TIA-232 and V.28/V.24 communications interfaces with automatic shutdown/wakeup features, high data- rate capabilities, and enhanced electrostatic discharge (ESD) protection.