Intersil manuals, page 24
intersil ICL7673 Manual(1)
The ICL7673 is a low-cost transistor from Intersil that is used in power switching applications. It can automatically switch between two power supplies, and will automatically switch to the backup supply in the event of a failure in the main supply.
INTERSIL EL7554 Manual
The EL7554 is a full-feature synchronous 4A step-down regulator capable of up to 96% efficiency
INTERSIL ISL6269 handbook
ISL6269 is Intersil's Robust Ripple Regulator (R3) technology that delivers truly superior dynamic response to input voltage and output load transients. Integrated MOSFET drivers, 5V LDO and bootstrap diode result in fewer components and smaller implementation area.
INTERSIL FN7415.2 EL7640 EL7641 EL7642 handbook
EL7640, EL7641, EL7642 are high-performance TFT-LCD DC/DCs, integrated with 2 LDO controllers and adjustable delay VON-slice circuit, and one (EL7640), three (EL7641) or five amplifiers (EL7642) for VCOM and VGAMMA applications.
intersil ISL43681/ISL43741 handbook
The Intersil ISL43681 and ISL43741 devices are precision, bidirectional, analog switches configured as an 8 channel and a differential 4 channel multiplexer/demultiplexer.
intersil X98027 handbook
The X98027 275MHz Triple Video Digitizer with Digital PLL
intersil HGTP10N40C1/40E1/50C1/50E1 HGTH12N40C1 40E1 50C1 50E1 handbook
This document describes the features and characteristics of the HGTP10N40C1, 40E1, 50C1, 50E1 and HGTH12N40C1, 40E1, 50C1, 50E1 models of 10A, 12A, 400V and 500V N-Channel IGBTs, such as low on-state voltage, fast switching speeds, high input impedance, etc. These devices are suitable for power supplies, motor drives, and protection circuits.
intersil FRK264D FRK264R FRK264H 34A 250V 0.120 Ohm Rad Hard N-Channel Power MOSFETs
This document introduces three models of N-channel power MOSFETs, FRK264D, FRK264R, and FRK264H, with features including 34A current, 250V voltage, 0.120 ohm RDS(on), radiation hardness, neutron hardness, and dose hardness.
INTERSIL -ISL60002 handbook
ISL60002 is a low power precision analog voltage reference produced by Intersil, which has ultra-low static current (400nA), can work at a supply voltage of 2.7V to 5.5V, and has an initial accuracy of ±1.0mV and <<10ppm/√1kHrs long-term stability.
INTERSIL HIP6004B Buck Synchronous-Rectifier (PWM) Controller Output Voltage Monitor
The HIP6004B is one of the HIP6000 series PWM controllers that integrates all of the control, output adjustment, monitoring and protection functions into a single package, providing complete control and protection for a DC-DC converter optimized for high-performance microprocessor applications.
intersil EL4332 handbook
EL4332 is a triple very high speed 2:1 Multiplexer- Amplifier from Elantec. It is intended primarily for component video multiplexing and is especially suited for pixel switching. All three amplifiers are switched simultaneously from their A to B inputs by the TTL/CMOS compatible, common A/B control pin. A -3dB bandwidth of 300MHz together with 3ns multiplexing time enable the full performance of the fastest component video systems to be realized.
intersil HA-2540 handbook
HA-2540 is a high performance operational amplifier from Intersil that features high output power and low noise characteristics. It is suitable for large signal audio and video circuits.
intersil HIP1011B handbook
HIP1011B is the third product in the HIP1011 family and is an electronic circuit breaker that monitors, reports and protects circuits from excessive load currents. As a pin-for-pin drop-in alternative offering similar functionality to the widely used HIP1011, the HIP1011B is compatible with CompactPCI peripheral boards and PCI Hot Plug systems where voltage “health” monitoring and reporting are centralized by the system controller IC. The HIP1011B does not monitor nor respond to under voltage conditions thus making control of a wide range of voltages possible. The HIP1011B creates a small and simple yet complete power control solution to control the four independent supplies (+5V, +3.3V, +12V, and -12V) found in PCI and CompactPCI systems. For the +12V and -12V supplies, overcurrent protection is provided internally with integrated current sensing FET switches. For the +5V and +3.3V supplies, overcurrent protection is provided by sensing the voltage across the external current-sense resistors. The PWRON input controls the state of both internal and external switches. During an overcurrent condition on any output, all MOSFETs are latched-off and a LOW (0V) is asserted on the FLTN output. The FLTN latch is cleared when the PWRON input is toggled low again. During initial power-up of the main VCC supply (+12V), the PWRON input is inhibited from turning on the switches, and the latch is held in the Reset state until the VCC input is greater than VCCREF.
intersil X98021 datasheet
the x98021 is a 210mhz triple video digitizer with digital pll produced by intersil. it supports rgb or yuv video signal acquisition, with a maximum sampling rate of 210ms/s and a maximum resolution of uxga.
intersil EL5611/EL5811 handbook
EL5611 and EL5811 are low power, high voltage rail-to-rail input-output amplifiers primarily targeted at VCOM applications in TFT-LCD displays. The EL5611 contains six amplifiers, and the EL5811 contains eight amplifiers. Operating on supplies ranging from 5V to 15V, while consuming only 2.5mA per amplifier, the EL5611 and EL5811 have a bandwidth of 60MHz (-3dB). They also provide common mode input ability beyond the supply rails, as well as rail-to-rail output capability. This enables these amplifiers to offer maximum dynamic range at any supply voltage. The EL5611 and EL5811 also feature fast slewing and settling times, as well as a high output drive capability of 65mA (sink and source). In addition to VCOM applications, these features make these amplifiers ideal for high speed filtering and signal conditioning application. Other applications include battery power, portable devices, and anywhere low power consumption is important. The EL5611 is available in 8-pin MSOP and 8-pin HMSOP package.