Intersil manuals, page 19
intersil CD40257BMS CMOS Quad 2 Line to 1 Line Data Selector/Multiplexer handbook
intersil BTS436L2 handbook
This document describes a smart high-side power switch product with features such as low standby current, short circuit protection, and overload protection. It is suitable for microcontroller-compatible high-side power switches for 5V, 12V, and 24V grounded loads.
intersil HIP6521 PWM Triple Linear Power Controller handbook
The HIP6521 provides the power control and protection for four output voltages in high-performance microprocessor and computer applications. The IC integrates a voltage-mode PWM controller and three linear controllers, as well as monitoring and protection functions. The PWM controller is intended to regulate the microprocessor memory core voltage with a synchronous-rectified buck converter. The linear controllers are intended to regulate the computer system’s AGP 1.5V bus power, the 2.5V clock power, and the 1.8V power for the North/South Bridge core voltage and/or cache memory circuits. Both the switching regulator and linear voltage references provide ±2% of static regulation over line, load, and temperature ranges. All outputs are user-adjustable by means of an external resistor divider. All linear controllers employ bipolar NPNs for the pass transistors. The HIP6521 monitors all the output voltages. The PWM controller’s adjustable overcurrent function monitors the output current by using the voltage drop across the upper MOSFET’s rDS(ON). The linear regulator outputs are monitored via the FB pins for undervoltage events.
intersil EL5192 EL5192A Data Sheet
The EL5192 and EL5192A are current feedback amplifiers with a very high bandwidth of 600MHz. This makes these amplifiers ideal for today’s high speed video and monitor applications. With a supply current of just 6mA and the ability to run from a single supply voltage from 5V to 10V, the amplifiers are also ideal for hand held, portable or battery-powered equipment. The EL5192A also incorporates an enable and disable function to reduce the supply current to 100µA typical per amplifier. Allowing the CE pin to float or applying a low logic level will enable the amplifier. The EL5192 is offered in the 5-pin SOT-23 package and the EL5192A is available in the 6-pin SOT-23 as well as the industry-standard 8-pin SO packages. Both operate over the industrial temperature range of -40°C to +85°C.
intersil ACTS541MS Radiation Hardened Octal Three-State Buffer/Line Driver handbook
This document describes the pinouts, features, and characteristics of the ACTS541MS radiation hardened octal three-state buffer/line driver. The product is QML qualified and complies with MIL-PRF-38535. It is manufactured using a 1.25-micron radiation hardened SOS CMOS process and exhibits high radiation tolerance and single event upset immunity. The device is latch-up free under any conditions and operates within the military temperature range. It offers significant power reduction compared to ALSTTL logic.
intersil ISL6227 handbook
ISL6227 Dual Mobile-Friendly PWM Controller with DDR Option
intersil ISL1557 handbook
ISL1557 is a dual operational amplifier designed by Intersil for VDSL2 and ADSL line driving in DMT based solutions. This device features a high drive capability of 750mA while consuming only 6mA of supply current per amplifier and operating from a single 4.5V to 12V supply. The driver achieves a typical distortion of -80dBc, at 150kHz into a 25Ω load. The ISL1557 is available in the thermally-enhanced 16 Ld QFN package and is specified for operation over the full -40°C to +85°C temperature range. The ISL1557 has control pins C0 and C1 for controlling the bias and enable/disable of the outputs. These controls allow for lowering the power to fit the performance/power ratio for the application. The ISL1557 is ideal for ADSL2+, SDSL, HDSL2 and VDSL line driving applications, including both 14.5dBm and 21dBm applications.
intersil EL8170 EL8173 handbook
The EL8170 and EL8173 are micropower instrumentation amplifiers optimized for operation at 2.9V to 5V single supplies. Inputs and outputs can operate rail-to-rail.
intersil EL5285 handbook
EL5285 is a high-speed comparator from Intersil. It features 4ns typical propagation delay, 5V to 12V power supply voltage range, 2.7V to 5V output voltage range, and can be directly connected to CMOS and TTL logic circuits.
intersil EL5144 EL5146 EL5244 EL5246 EL5444 handbook
1 ® FN7177.1 EL5144, EL5146, EL5244, EL5246, EL5444 100MHz single-supply rail-to-rail amplifiers
intersil EL4543 handbook
EL4543 is a high bandwidth triple differential amplifier with integrated encoding of video sync signals
intersil CDP1805AC CDP1806AC handbook
Describes the features and characteristics of CDP1805AC and CDP1806AC, including instruction time, temperature range, instruction number, upward compatibility, low-power IDLE mode, pin compatibility, memory address capability, memory capacity, register matrix, crystal or RC controlled oscillator, 8-bit counter/timer.
intersil CA3306/CA3306A/CA3306C Manual
intersil CA3262A/CA3262 Manual
The CA3262 and CA3262A are used to interface low-level logic to high current loads. Each Power Driver has four inverting switches consisting of a non-inverting logic input stage and an inverting low-side driver output stage. All inputs are 5V TTL/CMOS logic compatible and have a common Enable input. Each output device has independent current limiting (ILIM) and thermal limiting (TLIM) for protection from over-load conditions. Steering diodes connected from each output (in pairs) to the Clamp pins may be used in conjunction with external zener diodes to protect the IC against over-voltage transients that result from inductive load switching. To allow for maximum heat transfer from the chip, all ground pins on the DIP, PLCC and SOIC packages are directly connected.
intersil IRF140 Manual
IRF140 is a power MOSFET produced by Intersil. It has a rated current and voltage of 28A and 100V, respectively, and a conduction resistance of 0.077Ω.