TEXAS Manuals

UCC2540 is a high efficiency, high current, low output voltage secondary-side synchronous Buck PWM controller from TI. It is suitable for secondary-side post regulation (SSPR) applications for multiple output power supplies, as well as cascaded Buck converters and bus converter/DC transformer architectures.

GC5018 is a 8-channel wideband receiver from Texas Instruments, featuring 115 dB SFDR NCO, four 16-bit CMOS ADC input ports, programmable closed loop VGA control, 6-bit outputs, supporting UMTS mode Rx Filtering, CDMA mode Rx Filtering, etc.

This document is a datasheet about the features and characteristics of the product, providing detailed information about the product.

SN54HCT373 and SN74HCT373 are octal transparent D-type latches with 3-state outputs. They are suitable for driving highly capacitive or relatively low-impedance loads and are particularly suitable for implementing buffer registers, I/O ports, bidirectional bus drivers, and working registers.

This is a high precision, wide bandwidth, high output drive capability CMOS single supply rail to rail operational amplifier

The THS4041 and THS4042 are single/dual, high-speed voltage feedback amplifiers capable of driving any capacitive load. This makes them ideal for a wide range of applications including driving video lines or buffering ADCs. The devices feature high 165-MHz bandwidth and 400-V/µsec slew rate. The THS4041/2 are stable at all gains for both inverting and noninverting configurations. For video applications, the THS4041/2 offer excellent video performance with 0.01% differential gain error and 0.01° differential phase error. These amplifiers can drive up to 100 mA into a 20-Ω load and operate off power supplies ranging from ±5V to ±15V.

This document describes the features of Harris Semiconductor SCHS158E, including three-state buffered outputs, gated input and output enables, wide operating temperature range, balanced propagation delay and transition times, significant power reduction compared to LSTTL logic ICs, etc.

This data sheet introduces the features and characteristics of the DCP01B series. The DCP01B series is a family of 1W, unregulated, isolated DC/DC converters. It features up to 85% efficiency, thermal protection, device-to-device synchronization, short circuit protection, EN55022 Class B EMC performance, UL1950 recognized component, and JEDEC PDIP-14 and GULL-WING packages.

The CY74FCT162827T and CY74FCT16827T are 20-bit buffers/line drivers that provide high-performance bus interface buffering for wide data/address paths or buses carrying parity. These parts can be used as a single 20-bit buffer or two 10-bit buffers. Each 10-bit buffer has a pair of NANDed OE pins for increased flexibility. The outputs are designed with a power-off disable feature to allow for live insertion of boards. The CY74FCT16827T is ideally suited for driving high-capacitance loads and low-impedance backplanes. The CY74FCT162827T has 24mA balanced output drivers.

LMV321 is a single-channel, low-voltage, rail-to-rail output operational amplifier, LMV324 is a dual-channel, low-voltage, rail-to-rail output operational amplifier, LMV358 is a quad-channel, low-voltage, rail-to-rail output operational amplifier.

lm224ka,lm324ka,lm2902kav are low-power, high-gain, frequency-compensated operational amplifiers that are suitable for single-supply and dual-supply operation. Input bias current and offset voltage are small, and common-mode range includes ground, allowing direct sensing near ground.

This document describes the features and characteristics of TMS320LF2407, TMS320LF2406, and TMS320LF2402 chips. These chips utilize high-performance static CMOS technology and feature low-power 3.3V design and high performance. The chips have integrated Flash EEPROM, data/program RAM, dual-access RAM, and single-access RAM. Additionally, the chips have two event manager modules for pulse-width modulation control, external event capture, and other functionalities. They are suitable for various motor control applications including AC induction motors, brushless DC motors, switched reluctance motors, and stepper motors.

This data manual describes the features and usage of TMS320F2810, TMS320F2811, TMS320F2812 and TMS320C2810, TMS320C2811, TMS320C2812 Digital Signal Processors.

TM2SN64EPH and TM4SN64EPH are two synchronous dynamic random access memory (SDRAM) modules that can be used in 66MHz 4-Clock systems. They use a single 3.3V power supply and support read latencies 2 and 3. Both modules support byte read/write capability and have a high performance range, high speed, low noise, low voltage TTL (LVTTL) interface, support burst interleave and burst interrupt operations, burst length programmable to 1, 2, 4 and 8, have two banks for on-chip interleaving (gapless access), an ambient temperature range of 0°C to 70°C, gold-plated contacts, a pipeline architecture and use EEPROM for serial presence detection (SPD).