TEXAS Manuals (Industrial)

This document introduces the features and characteristics of the SN54AC14/SN74AC14 series products, including the operating voltage range, the input voltage range, the maximum propagation delay, etc.

File format: PDF Size:522 KB

File format: PDF Size:0 KB

The DAC7612 is a dual, 12-bit digital-to-analog converter (DAC) with guaranteed 12-bit monotonicity performance over the industrial temperature range. It requires a single +5V supply and contains an input shift register, latch, 2.435V reference, a dual DAC, and high speed rail-to-rail output amplifiers. For a full- scale step, each output will settle to 1 LSB within 7µs while only consuming 3.7mW. The synchronous serial interface is compatible with a wide variety of DSPs and microcontrollers. Clock (CLK), Serial Data In (SDI), Chip Select (CS) and Load DACs (LOADDACS) comprise the serial interface. The DAC7612 is available in an 8-lead SOIC package and is fully specified over the industrial temperature range of –40°C to +85°C.

File format: PDF Size:317 KB

This document introduces the features and characteristics of the TMP441 and TMP442 temperature sensors. These two products are packaged in SOT23-8 and have a maximum error of ±1°C for the remote diode sensor and a maximum error of ±1°C for the local temperature sensor. They also include automatic beta compensation, series resistance elimination, and η factor correction functions. Both products use the SMBus™ serial interface and support multiple interface addresses. They also have diode fault detection functions.

File format: PDF Size:735 KB

TPA2010D1 is a 2.5W high efficiency filter-free class-D audio power amplifier from TI, packaged as a 1.45mm x 1.45mm wafer chip scale package (WCSP) that requires only three external components.

File format: PDF Size:427 KB

The PCM4204 is a high-performance, four-channel analog-to-digital (A/D) converter designed for professional applications. It supports 24-bit linear PCM or 1-bit direct stream digital (DSD) output data, with PCM output sampling rates up to 216kHz and DSD output data rates of 64fS and 128fS.

File format: PDF Size:555 KB

The ADS7842 is a 12-bit, 4-channel parallel output sampling analog-to-digital converter (ADC) with features including single supply operation, a 4-channel input multiplexer, up to 200kHz sampling rate, full 12-bit parallel interface, ±1LSB INL and DNL, no missing codes, 72dB SINAD, and low power consumption. It is ideal for battery-operated systems such as portable, multi-channel dataloggers and measurement equipment.

File format: PDF Size:288 KB

The XTR110 is a precision voltage-to-current converter designed by Texas Instruments. It can accept inputs of 0 to 5V or 0 to 10V and can be connected to outputs of 4 to 20mA, 0 to 20mA, 5 to 25mA and many other commonly used ranges.

File format: PDF Size:665 KB

The SN74AHCT245 and SN54AHCT245 are octal bus transceivers designed for asynchronous two-way communication between data buses. The control-function implementation minimizes external timing requirements. The ’AHCT245 devices allow data transmission from the A bus to the B bus or from the B bus to the A bus, depending on the logic level at the direction-control (DIR) input. The output-enable (OE) input can be used to disable the device so that the buses effectively are isolated.

File format: PDF Size:739 KB

The DAC7744 is a 16-bit, quad voltage output digital-to-analog converter with guaranteed 16-bit monotonic performance over the specified temperature range. It is ideal for automatic test equipment, DAC-per-pin programmers, data acquisition systems, and closed-loop servo-control.

File format: PDF Size:478 KB

OPA2111 is a low-noise, high-precision, low bias current, high open-loop gain dual-channel operational amplifier produced by BURR-BROWN. Suitable for high-precision measurement, data acquisition, test equipment, professional audio equipment, medical equipment and other fields.

File format: PDF Size:194 KB

SN54ABT541, SN74ABT541B are octal buffers/drivers with 3-state outputs produced by TI.

File format: PDF Size:539 KB

The TPS62052 is a synchronous step-down converter from TI with high efficiency, low quiescent current, wide operating input voltage range, adjustable output voltage range and more. It is ideal for systems powered from a 1-cell or 2-cell Li-Ion battery or from a 3-cell to 5-cell NiCd, NiMH, or alkaline battery.

File format: PDF Size:445 KB

bq2002/F is a fast charge IC that supports fast charge for nickel cadmium or nickel metal hydride batteries. It can terminate fast charge by -∆V, maximum voltage, maximum temperature, and maximum time. bq2002/F also integrates optional top-off and pulse-trickle control in a single IC for charging one or more NiCd or NiMH battery cells.

File format: PDF Size:183 KB

The Harris CD54HC245, CD54HCT245, and CD74HC245, CD74HCT245 are high-speed octal three-state bidirectional transceivers with buffered inputs, three-state outputs, and bus driving capability.

File format: PDF Size:38 KB

The INA157 is a high-gain, low-drift, high common-mode rejection, high input bandwidth difference amplifier.

File format: PDF Size:283 KB

the tps718xx and tps719xx are low-noise, high psrr low-dropout linear regulators with 200ma output, low quiescent current, fast start-up, and excellent line and load transient response.

File format: PDF Size:843 KB

File format: PDF Size:0 KB

The TPA2032D1 is a 2.75-W fixed gain mono filter-free class-D audio power amplifier. It features WCSP packaging, high efficiency, and low power consumption, making it ideal for applications such as wireless handheld devices and mobile devices.

File format: PDF Size:1016 KB

The XTR115 XTR116 4-20mA current loop transmitters feature low quiescent current, 5V regulator, sensor excitation VREF, low span error, low nonlinearity error, wide loop supply range, SO-8 package

File format: PDF Size:415 KB