Industrial Manuals

This data brief provides details about the STEVAL-IFS017V5 temperature sensor daughter card, including features, description and schematic diagram

File format: PDF Size:80 KB

This is a temperature sensor daughter card based on STTS2002B2DN3F in TDFN8 package. It supports USB power and complies with RoHS standard.

File format: PDF Size:400 KB

This is a 3 A / 1.5 MHz step-down synchronous switching regulator based on the ST1S31 in DFN 3x3 package with the following features: 4 A peak output current, 2.8 V to 5.5 V input voltage, output voltage adjustable from 0.8 V, 1.5 MHz switching frequency, internal soft-start and enable, integrated 60 mΩ and 45 mΩ power MOSFETs, all ceramic capacitors, Power Good (POR), cycle-by-cycle current limiting, current foldback short-circuit protection, RoHS compliant.

File format: PDF Size:276 KB

This document describes the features and characteristics of the STEVAL-ISA078V1 high efficiency synchronous step-up regulator, including input voltage range, high efficiency, extremely low quiescent current, maximum output current, adjustable output voltage, low dropout operation, output voltage accuracy, and switching frequency.

File format: PDF Size:1093 KB

The STEVAL-ISA079V1 demonstration board is based on the DC-DC monolithic regulator L6928D, specifically designed to provide extremely high efficiency.

File format: PDF Size:255 KB

File format: PDF Size:0 KB

This document is the data brief of STEVAL-ISA103V1, which introduces the features and characteristics of the product, including input voltage range (90 V - 265 V), output voltage (5 V), output power (12 W), standby consumption, overload protection, secondary winding short-circuit protection, output overvoltage protection, brownout protection, etc.

File format: PDF Size:220 KB

The STEVAL-ILB009V1 is a 2x28W electronic ballast with active power factor correction (PFC) based on the STD3N62K3 and STD845DN40 BJT devices. It has an input voltage range of 180VAC to 264VAC, a nominal output voltage of 400V, a nominal output power of 60W, a target efficiency of approximately 90%, a minimum switching frequency of 35kHz, and an expected power factor of 0.99.

File format: PDF Size:211 KB

This document provides preliminary information on a new product currently in development or undergoing evaluation. Details are subject to change. For further information, please contact your local STMicroelectronics sales office.

File format: PDF Size:206 KB

EVAL6472H is a fully integrated stepper motor driver based on L6472, with a voltage range from 8V to 45V, maximum phase current of 3A, supports SPI interface and multi-motor applications, suitable for use in combination with STEVAL-PCC009V2.

File format: PDF Size:1177 KB

The STEVAL-MKI116V1 is a MEMS microphone demonstration board based on the MP34DB01 and STM32. It is powered and connected to a PC through USB and features digital MEMS microphones, high-frequency data stream, and LED status indicator.

File format: PDF Size:355 KB

This document introduces the features and characteristics of the STEVAL-MKI117V1 MEMS microphone demonstration board based on the MP34DT01 and STM32. The demonstration board can be connected to PC through USB and is automatically recognized as an audio device by PC.

File format: PDF Size:358 KB

This is a technical brief of ALTAIR05T-800, which is a 5W wide range CV-CC optoless adapter demonstration board, tailored for AC-DC chargers for mobile phones and adapters and other hand-held equipment.

File format: PDF Size:67 KB

This document describes the features and characteristics of a product called L6470. The product is a fully integrated stepper motor driver with a voltage range from 8V to 45V and a phase current up to 3Arms. It supports SPI with daisy-chain feature and has a socket for external resonator or crystal. It is suitable to be used in combination with STEVAL-PCC009V2. The product also has adjustable supply voltage compensation and is suitable for the evaluation of multi-motor applications.

File format: PDF Size:1761 KB

Data brief for STEVAL-ISV005V2 240 W photovoltaic battery charger based on the SPV1020

File format: PDF Size:328 KB

This data brief describes the STEVAL-ICB010V1 AirNavigationPad demonstration board, a PC HID peripheral that can be used to interact with the PC by sending commands in the same way as a PC mouse.

File format: PDF Size:237 KB

This data brief provides a detailed description of the STEVAL-TLL008V1 camera flash with SuperCap features, including different operating modes, LED current adjustment range, NTC function, status register, ATN pin, Ready pin, light sensor, etc.

File format: PDF Size:301 KB

This document describes the STMicroelectronics STEVAL-IPE010V2 energy meter demonstration kit motherboard, which is based on the STPMC1. It has various features and functions and can be used to design a Class 1 meter for 2 to 4-wire power line systems.

File format: PDF Size:184 KB

The document describes the EVAL6474H demonstration board, which is a microstepping motor driver. It is designed to be used in combination with the STEVAL-PCC009V2 communication board and the easySPIN evaluation software. The EVAL6474H supports daisy chain configuration and is suitable for evaluating the L6474 in multi-motor applications.

File format: PDF Size:1413 KB

The STEVAL-PCC015V1 demonstration board serves as a bridge between a standard USB port and a classical serial COM port. It implements the standard CDC class of USB and emulates COM port functionality to a standard USB port. The board implements RS232 full hardware flow control using RTS and CTS. The communication task between USB and RS232 (UART) is performed by the STM32 medium density line device. A standard DB9 connector (female) is used for RS232, allowing direct connection to a PC. The unit is bus-powered and RoHS compliant.

File format: PDF Size:206 KB