Industrial

MC74HC4051A/D, MC74HC4052A, MC74HC4053A are high performance silicon-gate CMOS devices featuring fast propagation delays, low ON resistances, and low OFF leakage currents. These analog multiplexers/demultiplexers control analog voltages that may vary across the complete power supply range (from VCC to VEE). The HC4051A, HC4052A and HC4053A are identical in pinout to the metal-gate MC14051AB, MC14052AB and MC14053AB. The Channel-Select inputs determine which one of the Analog Inputs/Outputs is to be connected, by means of an analog switch, to the Common Output/Input. When the Enable pin is HIGH, all analog switches are turned off. The Channel-Select and Enable inputs are compatible with standard CMOS outputs; with pullup resistors they are compatible with LSTTL outputs. These devices have been designed so that the ON resistance (Ron) is more linear over input voltage than Ron of metal-gate CMOS analog switches. For a multiplexer/demultiplexer with injection current protection, see HC4851A and HC4852A.

The file is the datasheet of 25AA1024/25LC1024

The TS461/2/4 is a family of low noise, low distortion, high dynamic range operational amplifiers that can operate with voltages as low as ±1.35V and to reach a minimum of ±2Vpp of output swing when supplied with ±2.5V.

This datasheet introduces the features and characteristics of the Cirrus Logic CS8900A product.

The LTC3719 is a 2-phase, VID programmable, synchronous step-down switching regulator controller that drives two N-channel external power MOSFET stages in a fixed frequency architecture. The 2-phase controller drives its two output stages out of phase at frequencies up to 300kHz to minimize the RMS ripple currents in both input and output capacitors. The 2-phase technique effectively multiplies the fundamental frequency by two, improving transient response while operating each channel at an optimum frequency for efficiency. Thermal design is also simplified. An operating mode select pin (FCB) can be used to select among three modes including Burst Mode operation for highest efficiency. An internal differential amplifier provides true remote sensing of the regulated supply’s positive and negative output terminals as required in high current applications. The RUN/SS pin provides soft-start and optional timed, short-circuit shutdown. Current foldback limits MOSFET dissipation during short-circuit conditions when the overcurrent latchoff is disabled. OPTI-LOOP compensation allows the transient response to be optimized for a wide range of output capacitors and ESR values. 2-Phase, High Efficiency, Step-Down Controller for AMD Opteron CPUs.

The LT1004 is a 2-terminal bandgap reference diode designed to provide high accuracy and excellent temperature characteristics at very low operating currents. It has an initial accuracy of ±4mV, an operating current of 10µA, and can operate up to 20mA.

The LP3992 regulator is a micropower 1.5V CMOS voltage regulator with shutdown control. It is designed for portable, battery-powered systems and provides an accurate output voltage, low noise, and low quiescent current. The LP3992 can prolong battery life by providing a 1.5V output from a low input voltage of 1.9V. It also features short-circuit and thermal-shutdown protection. The device is stable with small ceramic capacitors and is available in an SOT23-5 package.

The LTC1148 series is a family of synchronous step-down switching regulator controllers featuring high efficiency, current-mode operation, and low power consumption.

This is a PDF document about a 12-bit monitor and control system. The document introduces the AD7294 with multichannel ADC, DACs, temperature sensor, and current sense. The system features high accuracy, fast conversion time, and various input and output capabilities.

This datasheet provides detailed information on the MIC5219 500mA-Peak Output LDO Regulator, including its high peak output current capability, very low dropout voltage, better than 1% output voltage accuracy, 10mV typical dropout at light loads, less than 500mV maximum dropout at full load, 500mA peak output rating, continuous output current limited only by package and layout, CMOS or TTL compatible signal to enable or shut down the MIC5219, power consumption drops to nearly zero when disabled, minimized dropout ground current to help prolong battery life, reverse battery protection, current limiting, overtemperature shutdown, and low noise performance with an ultra-low-noise option.

MCP73871 is a lithium battery charger chip from Microchip, supporting 4.10V, 4.20V, 4.35V and 4.40V multiple charging voltage, supporting USB port and AC power supply.

The SFH610A / SFH6106 is a high reliability optocoupler with a 5300VRMS isolation voltage. This product features a high current transfer ratio, low coupling capacitance and high isolation voltage.

The LP2981 is a 100 mA, fixed-output voltage regulator designed specifically to meet the requirements of battery-powered applications. Using an optimized VIP™ (Vertically Integrated PNP) pro- cess, the LP2981 delivers unequaled performance in all specifications critical to battery-powered designs: Dropout Voltage. Typically 200 mV @ 100 mA load, and 7 mV @ 1 mA load. Ground Pin Current. Typically 600 µA @ 100 mA load, and 80 µA @ 1 mA load. Sleep Mode. Less than 1 µA quiescent current when ON/ OFF pin is pulled low. Smallest Possible Size. SOT-23 and micro SMD packages use an absolute minimum board space. Precision Output. 0.75% tolerance output voltages avail- able (A grade). Eleven voltage options, from 2.5V to 5.0V, are available as standard products.

ACSL-6xx0 is a fully digital logic gate optocoupler, providing full duplex and bidirectional isolated data transfer and communication capability. Available in 8-pin and 16-pin narrow-body SOIC packages and specified over the temperature range of -40°C to +100°C